• Discs that have labels printed using ink that fi.,elstacky
when touched
Notes on discs
• Befbre playing, wipe the disc with a cleaning cloth fl'om
the center out to the edge.
• Do not clean discs with solvents, such as benzine
thinner, or cotnmercially available cleaners or anti
static spray intended Ior vinyl LPs.
• Do not expose discs to direct sunlight or heat sources
such as hot air ducts, nor leave it in a car parked in
direct sunlight.
On safety
• The unit is not disconnected from the AC power source
(mains) as long as it is connected to the wall outlet,
even if the unit itself has been turned off.
• Completely disconnect the power cord (mains lead)
*_om the wall socket (mains) if it is not going to be used
*br an extended period of time. When unplugging the
unit, ahvays grip the plug. Never pull the cord itself.
• Should any solid object or liquid get into the system,
unplug the system, and have it checked by qualified
personnel betbre operating it again.
• The AC power cord can be changed only by a qualified
service lacility.
On placement
• Do not place the system in an inclined position or in
locations that are extremely hot, cold, dusty, dirty, or
humid or lacking adequate ventilation, or subject to
vibration, direct sunlight or a bright light.
• Be carefifl when placing the unit or speakers on
surfhces that have been specially treated (t}_rrexample,
with wax, oil, polish) as staining or discoloration of the
surfhce may result.
• If the system is brought directly ficom a cold to a warm
location or is placed in a very damp room, moisture
may condense on the lens inside the CD player, and
cause the system to malfunction. In this situation,
remove the disc, and leave the system turned on fbr
about an hour until the moisture evaporates.
On heat buildup
• Heat buildup on the unit during operation is normal
and is not cause *bralarm.
• Do not touch the cabinet ifit has been used
continuously at a high volume because the cabinet may
have become hot.
• Do not obstruct the ventilation holes.
On the speaker system
This speaker system is not magnetically shielded, and
the picture on nearby TV sets may become magnetically
distorted. In this situation, turn off the TV, wait 15 to 30
minutes, and turn it back on.
If there is no improvement, move the speakers fhr away
from the TV.
Cleaning the cabinet
Clean this system with a soft cloth slightly moistened
with a mild detergent solution. Do not use any type
of abrasive pad, scouring powder, or solvent, such as
thinner, benzine, or alcohol.
To prevent a tape from being accidentally
recorded over
Break off the cassette'soverwrite protection tab from side
A or B as illustrated.
__ B2_ak0ffthe cassette
Tolater reuse the tape ior recording, cover the broken tat)
with adhesive tape.
About a tape longer than 90 minutes
The use of the tape with more than 90 minutes of play
time is not reconunended except *br long, continuous
recording or playback.
Cleaning the tape heads
Use dry- or wet-type cleaning cassette (available
separately) after every 10 hours of use, befbre yon start an
important recording, or after playing an old tape. Failure
to clean the tape heads can cause degraded sound quality
or an inability of the unit to record or play tapes. For
details, refi.,r to the instructions of the cleaning cassette.
Demagnetizing the tape heads
Use a demagnetizing cassette (available separately) after
every 20 to 30 hours of use. Failure to demagnetize
the tape heads can cause an increase in noise, a loss of
high f}cequency sound, and an inability to completely
erase tapes. For details, refer to the instructions of the
demagnetizing cassette.
Main unit
AUDIO P()WER SPLCIFICArHONS
PO%'ER ()U'I pUrF AND TO'IAh t{ARM()NIC DIS'I ()R'I ]()N:
(MttC GX99, MH( tC77 lhe United Statesmodel only)
ho_ channd
_Vith 8 ohm loads, both channds dliw'n, horn 121/ 10d/00 Hz; 60 watts
p_q (-halll]_,ll]anJmlll_l R_IS pow_,r, with no mor_' Lhal] 0.7% total hal mollie
distol tkln tlom 250 milliwatt s to rated ou{put.
]tJgh channd
With 8 ohnl klads, both channels (hlv¢'n, horn 2,000 13,000 ]Jz;60 watts
p_,l ch_tnlJPl llanJmllnl RI\IS powcT, with no mor_' thai] 0.7% total hal monic
distol tion tlOlI12511 l_]illJwatts 1o rat_'d Olllpllt.
AUDIO P()WER SPLCIFR2ATIONS
P()%'ER ()U'I PUT AND "lO'IAh ttARMONIC DIS'I ()R'I ]ON:
(MIIC t£55 "[h_' Unaed Stat_s modal only)
With 6 ohm klads, both channels diiw'n, horn 120 10,000 HZ; 45 watts
p_q (-h_tnlJPl llanJmllnl RI\IS pow€,l, with no mor_, thai] 0.7% total hal monic
distol tkm horn 250 millix_alts to rated ou{put.
Amplifier section
MHC-GXPD
Front speaker:
RMS output power (reI_,rence):
ho,a channel
95 W + 95 W (per channel at 8 fL I kt tz, 10% Tt tD)
ttigh channd
95 W + 95 W (per channel at 8 fL 8 kt tz, 10% Tt tD)
Sub_)oter:
RMS output power (ret_,rence):
15(}W (at 6 fL 8(I Hz, 10% TH [))
MHC-E{77
Noith Anlelican modal:
RMS output power (lel_'r_'nc_'):
ho_ channel
95 "W + 95 %"(per channel ,it 8 f_, 1 kt tz, 10% Tt ]D)
ttigh channd
95 W + 95 W (per channel at 8 t'_, 8 kttz, 1(1%TttD)
European and Russian modds:
Power output (rated):
Lo% dlanlld
45W + 45 %"(at 8 tl, I ktlz, 1% THD)
ttigh channd
45 W + 45 W (at s £_, s kHz, 1% TIt D)
RMS output power (rel_,rence):
how channel
65 W + 65 W (per channel at 8 fl, I kt tz, 1(1%Tt tD)
ttigh channd
65 W + 65 W (per channel at 8 fL 8 kt {z, 1(1%Tt ]D)
()tiler models:
lhe tollowing are meastlred at AC 120, 127, 220, 24(I V, 50/60 t tz
Power output (rated):
how channel
50 W + 50 V; (at 8 tl, I ktlz, 1% THD)
ttigh channd
5(I W + 50 %"(at 8 tl, 8 kHz, 1% THD)
RMS output power (rel_,rence):
ho_ channel
70 W + 70 W (per channel at 8 fL I kt tz, 1(1%TItD)
ttigh channd
70 W + 70 W (per channel at 8 fL 8 kt tz, 1(1%Tt ]D)
MHC-EC55
North American model:
RMS output power (re,fence):
65 W+ 65 W (per channel at 6 _. l kt tz, 10% Ttt D)
European and Russian lllodds:
Power {_l_(tt (rated): 45 W + 45 W (at 6 _, I kHz, 1% TttD)
RMS output power (reference):
65 W + 65 %" (per dlannel at 6 f_, 1 kt tz. 10% Tt tD)
Other models:
lhe _llowing are measured at AC 120, 127, 220, 24(} _ 5(I/60 t tz
Power {_l_(tt (rated): 45 W + 45 W (at 6 _, I kHz, 1% TttD)
RMS output power (reference):
65 W + 65 %" (per dlannel at 6 f_, 1 kt tz. 10% Tt tD)
Inputs
AUDI() IN (stereo mha )ack): Sensitivay 800 m_ impedance 47 kik)hms
Outputs
PHONES (stereo mini iack): Accepts headphones wah an impedance of 8 f_
or more
SPEA KEP.: Accepls impedance of 6 to s f2
SUB%'O()FER ()UT/Mt tC GX99 only)
CD player section
System: Compact disc and digital audio system
haser:Semiconductorlaser(X 770 810nm)
Eltdssion dur_ion: conth_(lous
Frequency response: 20 ttz 20 kttz
Signal to noise r_io: More than 90 dB
Dynamic range: More than 88 dB
Tape deck section (Except for North American model)
Recording syslem: 4 track 2 channd, slereo
Tuner section
FM stereo. FM/AM superheterodyne tuner
Antenna:
FM lead antenna
AM k!op antenna
FM tuner section:
"hming range
North American model: 87.5 108.0 Mttz ( 100 kt tz step)
()ther models: 87.5 108.0 Mttz (5(I kttz step)
Intermediate fre_lency: 10.7 Mt tz
AM tuner section:
"hming range
Fall American and Australian li_odels:
53(} 1,7 l0 kHz (with 10 kttz tuning interval/
531 1,7 l0 kt tz (with 9 kttz tuning interval)
European, _tssian and Saudi Arabian models:
531 1,6(12 kltz (with 9 kHz tuning interval)
Other models:
53(} 1,6 l0 kHz (with 10 kttz tuning interval/
531 1,6(12 kltz (with 9 kHz tuning interval/
hltermediale frequency: 450 kt tz
Speaker
SS-EC77 for MHC-6XP_/EC77
Speaker system: 3 wa}q 3 unit. bass reflex type
Speaker (mi_
%roofer: 15 cm × 2, cone type
"I weeter: 4 cm. horn _pe
Nominal impedance: s f_
Dimensions (w/h/d): Approx. 220 × 36(I × 22(I mm
Mass: Approx. 3.6 kg net per speaker
Subwoofer _A-W6P9 for MHC-6XPP only
Speaker system: bass rellex type
Speaker (mi_
%roolhr: 2(} cm. cone type
Nominal impedance: 6 f_
Dimensions (w/h/d): Approx. 280 × 3(}6 x 4(15 mm
Mass: Approx. 8.7 kg
SS-EC55$/SS-E{55 for MH{-EC$5
Speaker system: 2 wa}q 2 unit. bass reflex type
Speaker (mi_
_Aroo fer: 16 cm. cone type
lweeter: 4 cm. horn type
Nominal impedance: 6 f_
Dimensions (w/h/d): Approx. 215 × 3(}6 × 215 mm
Mass: Approx. 2.8 kg net per speaker
(;eneral
Powerrequirements:
North Anwiican too(M: A( 120 \2 60 Hz
Emop_,an and Russian models: AC 230 _ 50/60 Hz
AustialJan model: AC 230 24(} _,, 50/60 t ]z
Mexican modal: AC 127\i 60 Hz
Arg_'ntine modal: A( 22(} \,_ 5(}/6(}Hz
Kolean modal: AC 220 \_ 60 Hz
Sa_tdi Alabian model: AC 12(} 127, 22(} 24(} \25(}/6(I Hz, adiustable _ith
voltage selector
Other modds: AC 12(I,220 or 23(I 240 \i 5(I/6(I Hz, adiustahle wah w_ltage
selector
Powerconsumption:
MHC-6XPP
USA model: 190 W
Canadian modd: 245 VA
SA-W(;PP(Subwoofer)
USA model: 115 W
Canadian modal: 155 VA
MHC-EC77
USA model: 19(}W
Canadian model: 245 VA
European and Russian models: 140 W
(}.5W (in I_)wer Saving Mode)
Other modds: 150 W
MHC-EC$$
USA model: 95 W
Canadian model: 130 VA
European and Russian lnodds: 95 W
(I.5 W (in Power Saving Mode)
Other modds: 95 W
Dimensions(w/h/d) (exd, speakers):
Appl ox. 2(}(}× 306 x 410 mm
Mass(exd. speakers):
MHC-GXPP
North American modd: Approx. 6.1 kg
MD(-EC77
Nolth American aM Emop_'an modds: Approx. 6.1 kg
Other modds: Approx. 6.4 kg
MHC-EC$$
Nolth American nlodd: Approx. S.0kg
Other modds: Approx. 5.3 kg
Supplied accessolies: R_'mote Comn_ander ( I)/R6 (Size AA) batte_i_s (2)/t'M
k'ad/AM loop anwnna (l)/Speaker pads MttC (,X99 (8) aM 1o_SA W(,99
(Subwooh'r) (4) MttC EC77/EC55 (8)/Sub_oofe_ cabk' (MttC (,X99 only)
(D
Design and specifications ale subioct to changP _ithout notice'.
_ S_andby power consumption: 0.5 W
• Halogenated flame re_ardants are not used in fl_e
cerbdn printed wiring boards.
• Halogenated flame retardants are not used in cabinets.
(Excq_ for fire United Sb_tes modal)
To Previous Page
Loading...
