Sony SVS151 Series - Page 2

Sony
VAIO
and
CLIE
are
trademarks
or
regis
Caution
Ma rkings
for
Lithium/Ion
Battery
The
Sony
,
VAIO
and
CLIE
are
trademarks
or
regis
-
teredtrademarks ofSony. Microsoft, Windows,
WindowsMedia, Outlook, Bookshelfand other
Microsoft products are trademarks or registered
trademarks of Microsoft Corporation in the
United States and other countries. The word
Bluetooth and the Bluetooth logo are trademarks
f
Bl t th
SIG
I
AMD
th
AMD
l
th
Caution
Ma rkings
for
Lithium/Ion
Battery
-
The
follow ing or similartextsshall be provided on
battery pack of equipment or in both the operating
and the service instructions.
CAUTION: Danger of explosion if battery is
incorrectly replaced. Replace only with the same
ilt
t
dd
b
th
o
f
Bl
ue
t
oo
th
SIG
,
I
nc.
AMD
,
th
e
AMD
l
ogo, o
th
e
r
AMD product names and combinations thereof
are tra demarks ofAdvanced Micro Devices, Inc.
Intel Inside logo, Pentium, Celeron and Core are
trademarks or registered trademarks of Intel Cor-
poration. Transmeta, the Transmeta logo, Crusoe
Processor, the Crusoe logo and combinations
th f
td k
f
Tt
Cti
o
r
equ
i
va
l
en
t
t
ype recommen
d
e
d
b
y
th
emanu-
facturer. Discard used batteries according to the
manufacturer’s instructions.
CAUTION: The battery pack used in this device
may present afi re or chemicalburnhazard if mis-
treated. Do not disassemble, heat above 60C
(
140
F)
ii t
Di
f
d
btt
th
ereo
f
are
t
ra
d
emar
k
so
f
T
ransme
t
a
C
orpora
ti
on
in the USA and other countries. Graffi ti, Hot-
Sync, PalmModem, and Palm OSare registered
trademarks, and the Hotsync logo a nd Palm are
trademarks of Palm, Inc. or its subsidiaries. (M)
and Motrolaare trademarks of Motrora, Inc. Other
Motrola products and services with (R) mark like
(
140
F)
or
i
nc
i
nera
t
e.
Di
spose o
f
use
d
b
a
tt
er
y
promptly. Keep away from children.
CAUTION: Changing the back up battery.
• Overcharging, short circuiting, reverse charg-
ing, multilation or incineration of the cells must
be avoided to prevent one or more of the fol-
Dragomball are the trademarks of Motrola,Inc.
All other names of systems, products and services
in this manual are trademarks or registered trade-
Marks of their respective owners. In this manual,
the (TM) or (R) mark are not specified.
lowing occurrences; release of toxic materials,
release of hydrogen and/or oxygen gas, rise in
surface temperature.
•Ifacell hasleaked or vented, it should be
replaced immediately while
avoiding to touch
it without any protection.
The components identified by mark contain
confidential information.
Strictly follow the instructions whenever the
components repaired and/or replaced.
2
Service and Inspection Precautions
1. Obey preca utionary markings and
Instructions
Labels a nd stamps on the cabinet, chassis, and
components identify areas requiring specialpre-
cautions
Be
sure
to
observe
these
precautions
4. Inspect after completing service
After servicing, inspect to make sure that all
screws, components, and wiring have been
returned to their original condition. Also check
the areaaround the re
p
ai
r
location to ensure that
cautions
.
Be
sure
to
observe
these
precautions
,
as well as all precautions listed in the operating
manual and other associated documents.
2. Use designated parts only
The set’s components possess important safety
htiti
h
b tibilit
d
p
repair work hascaused no damage, and confirm
safety.
5. When replacing chip
components...
c
h
arac
t
er
i
s
ti
cs, suc
h
as noncom
b
us
tibilit
y an
d
the ability to tolerate large voltages. Be sure that
replacement parts possess the same safety charac-
teristics as the originals. Also remember thatthe
mark, which appears in circuit diagrams and
parts lists, denotes components thathave particu-
larly important safety functions; be extra sure to
lthd i td t
Neve
r
reuse components. Also remembe
r
that
the negative side of tantalum capacitors is easily
damaged by heat.
6. When handling flexible print
boards...
Μ
use on
l
y
th
e
d
es
i
gna
t
e
d
componen
t
s.
3. Always follow the original design
when mounting parts and routing
Wires
The
original
layout
includes
va rious
safety
fea
• The temperature of the soldering-iron tip
should be about 270C.
• Do not apply the tip more than three times to
the same pattern.
•Handle patterns with care; never apply force.
The
original
layout
includes
va rious
safety
fea
-
tures, such as inclusion of insulating materials
(tubes and tape) and the mounting of parts above
the printer boa rd. In addition, internal wiring has
been routed and clamped so as to keep it away
from hot or high-voltageparts. When mounting
parts or routingwires, therefore, be sure to du-
Pli t th i i l l t
Caution: Remember thathard disk drives are
easily damaged by vibration. Always handle
with care.
Pli
ca
t
e
th
e or
i
g
i
na
ll
ayou
t
.
2
[Sony Confidential]
SVS151 Series (9-890-888-XX)