Sony U-matic S VO-6800PS - Page 12

Pause operation
To
stop
the
tape
erenianly
during
camera
recording,
press
the
rernote
control
switch
on
the
camera
or
the
PAUSE
button
on
the
recorder.
The
PAUSE
lamp
on
the
recorder
will
blink
during
the
pause
mode.
The
E-to-E.
mode
signal
will
remain
displayed
on
the
monitor
con-
nected
to
the
recorder.
To
release
the
pause
mode,
press
the
remote
control
switch
on
the
camera
again
or
the
PAUSE
button
on
the
recorder.
elf
the
recording
has
been
started
with
the
PAUSE
but-
ton
on
the
recorder,
it
can
be
stopped
with
the
PAUSE
button
and
also
with
the
remote
contro!
switch
on
the
camera.
e!f
the
recording
has
been
started
with
the
remote
con-
tro!
switch
on
the
camera,
it
can
be
stopped
only
with
the
remote
control
switch.
The
PAUSE
button
cannot
stop
recording.
;
eThe
pause
mode
will
be
automatically
released
after
about
8
minutes
of
use,
and
the
recorder
will
set
in
the
stop
mode,
in
order
to
protect
the
tape
and
the
video
heads.
To
check
the
video
signal
being
recorded
(simultaneous
playback
picture)
To
check
whether
or
not
the
camera
recording
is
correct-
ly
made,
press
the
return
video
button
on
the
camera.
While
the
return
video
button
is
pressed,
the
simultaneous
playback
picture
is
displayed
on
the
viewfinder
screen,
with
the
tape
remaining
time
indica-
.
tion.
Tape remaining time indication
During
recording,
while
the
return
video
button
on
the
camera
is
pressed,
the
tape
remaining
time
is
displayed
on
the
simultaneous
playback
picture.
O ie)
REC/TALLY BATT
[i
cei remain- 20 15 10
cei time
15 | 10
Indication MIN | MIN MIN MIN
* The indication disappears.
ees MIN |BEFORE *.
If the tape will not run in the record mode
The
tape
will
not
run
if
a
video
signal
is
not
supplied.
If
this
happens,
check
the
pointer
of
the
CH-1
LEVEL
meter.
When
the
METER
SELECT
switch
is
set
to
VIDEO,
it
should
be
in
the
blue
zone,
indicating
a
sufficiently
strong
video
signal.
Stereo sound recording
To
record
stereo
sound,
connect
the
microphones
to
the
AUDIO
IN
CH-1/L/DUB
and
CH-2/R
connectors.
Set
the
CH-1
MIC/LINE
and
CH-2
MIC/CAMERAILINE
selectors
* to MIC.
When
the
microphone
is
eoarectad
to
the
AUDIO
IN
CH-
~
2/R connector, the microphone built into, or connected
to, the camera will be automatically disconnected.
12
0 min.
ASSEMBLY RECORDING
Two video sources—-one from the VIDEO IN connector,
the other from the CAMERA connector—can be
assembled by switching the VIDEO IN selector.
For instance, suppose two cameras are used as
sources. (For the connections, refer to pages 10 and 11.)
i Connect the camera cable of one camera |
(Camera 1) to the CAMERA connector and ‘the
video output connector of the other camera
(Camera 2) to the VIDEO IN connector.
2 Press the REC button on the recorder and ad-
just each camera while monitoring the
viewfinder or the monitor screen.
Turn the VIDEO IN selector to view each
camera.
3 Set the VIDEO IN selector to CAMERA for
Camera lt. -
4 While pressing the REC button, press the PLAY
button and start recording by pressing the
remote control switch on the camera.
5 At the desired point, stop recording by pressing
the remote control switch on the camera again.
6 Setthe VIDEO IN selector to LINE for Camera 2.
7 Continue recording by pressing the PAUSE but-
ton on the recorder after the VIDEO IN selector
is set to LINE for more than 3 seconds.
When assembly is finished, press the STOP button on
the recorder.
Picture of Camera 1 Picture of Camera 2
CAMERA * LINE
VIDEO IN
selector
elf two cameras are synchronized with the same
reference signal, you can smoothly change the picture
from one camera to another during tape running
(without using the pause mode) simply by switching the
VIDEO IN selector.