Spanset Gotcha Remote Rescue Kit - Page 24

24
Anchorage at foot level.
1. Access casualty’s anchorage point.
2. Attach the anchor sling to a suitable anchor point
above the casualty.
3. The rescuer will use their legs to help pull in the rope.
The single pulley is clipped to the anchor sling.
4. Adjust pole to the required length.
5. Attach the red clip to the end of the pole, and clip the
double pulley into the webbing.
6. Adjust ropes in-between the pulleys to the same
length as the pole.
7. Set the red clip to open.
8. Using the pole, attach the red clip to the casualty’s
harness attachment.
9. Remove the pole from the red clip.
10. Attach the GRIGRI to the rescuers harness.
11. Pull the slack rope through the GRIGRI to tension the
system, and squat down.
12. The rescuer now stands up, thus raising the casualty.
13. With one hand, the rescuer holds the rope below the
GRIGRI, close to the attachment sling. With the
other hand they take in the slack rope as they squat
down.
14. Once the casualty’s weight has been transferred to
the GOTCHA™ then their lanyard can be
disconnected.
15. The casualty can now be lowered as follows.
16. To lower the casualty the rescuer must take hold o
f
the rope that exits the GRIGRI, and this is used to
control the descent.
17. With the other hand releases the black handle on the
GRIGRI until the rope can be fed at a controllable
speed. This thus lowers the casualty.(Please see
note)
INSTALLATION & USE : INSTRUCTIONS
LOW
ANCHOR
Green Pulley to Anchor Sling
5
7
11-13
8
17
NOTE: In order to carry out a rescue the rescuer requires a harness with a front point of attachment for locating the GRIGRI.
If the anchor point for the GOTCHA™ is such that the casualty must be lowered, then the rope length in the kit must
be four times the distance from the anchorage to the point of safety.
Anchorage at foot level.
1. Access casualty’s anchorage point.
2. Attach the anchor sling to a suitable anchor point
above the casualty.
3. The rescuer will use their legs to help pull in the rope.
The single pulley is clipped to the anchor sling.
4. Adjust pole to the required length.
5. Attach the red clip to the end of the pole, and clip the
double pulley into the webbing.
6. Adjust ropes in-between the pulleys to the same
length as the pole.
7. Set the red clip to open.
8. Using the pole, attach the red clip to the casualty’s
harness attachment.
9. Remove the pole from the red clip.
10. Attach the GRIGRI to the rescuers harness.
11. Pull the slack rope through the GRIGRI to tension the
system, and squat down.
12. The rescuer now stands up, thus raising the casualty.
13. With one hand, the rescuer holds the rope below the
GRIGRI, close to the attachment sling. With the
other hand they take in the slack rope as they squat
down.
14. Once the casualty’s weight has been transferred to
the GOTCHA™ then their lanyard can be
disconnected.
15. The casualty can now be lowered as follows.
16. To lower the casualty the rescuer must take hold o
f
the rope that exits the GRIGRI, and this is used to
control the descent.
17. With the other hand releases the black handle on the
GRIGRI until the rope can be fed at a controllable
speed. This thus lowers the casualty.(Please see
note)
INSTALLATION & USE : INSTRUCTIONS
LOW
ANCHOR
Green Pulley to Anchor Sling
5
7
11-13
8
17
NOTE: In order to carry out a rescue the rescuer requires a harness with a front point of attachment for locating the GRIGRI.
If the anchor point for the GOTCHA™ is such that the casualty must be lowered, then the rope length in the kit must
be four times the distance from the anchorage to the point of safety.
Anchorage at foot level.
1. Access casualty’s anchorage point.
2. Attach the anchor sling to a suitable anchor point
above the casualty.
3. The rescuer will use their legs to help pull in the rope.
The single pulley is clipped to the anchor sling.
4. Adjust pole to the required length.
5. Attach the red clip to the end of the pole, and clip the
double pulley into the webbing.
6. Adjust ropes in-between the pulleys to the same
length as the pole.
7. Set the red clip to open.
8. Using the pole, attach the red clip to the casualty’s
harness attachment.
9. Remove the pole from the red clip.
10. Attach the GRIGRI to the rescuers harness.
11. Pull the slack rope through the GRIGRI to tension the
system, and squat down.
12. The rescuer now stands up, thus raising the casualty.
13. With one hand, the rescuer holds the rope below the
GRIGRI, close to the attachment sling. With the
other hand they take in the slack rope as they squat
down.
14. Once the casualty’s weight has been transferred to
the GOTCHA™ then their lanyard can be
disconnected.
15. The casualty can now be lowered as follows.
16. To lower the casualty the rescuer must take hold o
f
the rope that exits the GRIGRI, and this is used to
control the descent.
17. With the other hand releases the black handle on the
GRIGRI until the rope can be fed at a controllable
speed. This thus lowers the casualty.(Please see
note)
INSTALLATION & USE : INSTRUCTIONS
LOW
ANCHOR
Green Pulley to Anchor Sling
5
7
11-13
8
17
NOTE: In order to carry out a rescue the rescuer requires a harness with a front point of attachment for locating the GRIGRI.
If the anchor point for the GOTCHA™ is such that the casualty must be lowered, then the rope length in the kit must
be four times the distance from the anchorage to the point of safety.
Anchorage at foot level.
1. Access casualty’s anchorage point.
2. Attach the anchor sling to a suitable anchor point
above the casualty.
3. The rescuer will use their legs to help pull in the rope.
The single pulley is clipped to the anchor sling.
4. Adjust pole to the required length.
5. Attach the red clip to the end of the pole, and clip the
double pulley into the webbing.
6. Adjust ropes in-between the pulleys to the same
length as the pole.
7. Set the red clip to open.
8. Using the pole, attach the red clip to the casualty’s
harness attachment.
9. Remove the pole from the red clip.
10. Attach the GRIGRI to the rescuers harness.
11. Pull the slack rope through the GRIGRI to tension the
system, and squat down.
12. The rescuer now stands up, thus raising the casualty.
13. With one hand, the rescuer holds the rope below the
GRIGRI, close to the attachment sling. With the
other hand they take in the slack rope as they squat
down.
14. Once the casualty’s weight has been transferred to
the GOTCHA™ then their lanyard can be
disconnected.
15. The casualty can now be lowered as follows.
16. To lower the casualty the rescuer must take hold o
f
the rope that exits the GRIGRI, and this is used to
control the descent.
17. With the other hand releases the black handle on the
GRIGRI until the rope can be fed at a controllable
speed. This thus lowers the casualty.(Please see
note)
INSTALLATION & USE : INSTRUCTIONS
LOW
ANCHOR
Green Pulley to Anchor Sling
5
7
11-13
8
17
NOTE: In order to carry out a rescue the rescuer requires a harness with a front point of attachment for locating the GRIGRI.
If the anchor point for the GOTCHA™ is such that the casualty must be lowered, then the rope length in the kit must
be four times the distance from the anchorage to the point of safety.
Anchorage at foot level.
1. Access casualty’s anchorage point.
2. Attach the anchor sling to a suitable anchor point
above the casualty.
3. The rescuer will use their legs to help pull in the rope.
The single pulley is clipped to the anchor sling.
4. Adjust pole to the required length.
5. Attach the red clip to the end of the pole, and clip the
double pulley into the webbing.
6. Adjust ropes in-between the pulleys to the same
length as the pole.
7. Set the red clip to open.
8. Using the pole, attach the red clip to the casualty’s
harness attachment.
9. Remove the pole from the red clip.
10. Attach the GRIGRI to the rescuers harness.
11. Pull the slack rope through the GRIGRI to tension the
system, and squat down.
12. The rescuer now stands up, thus raising the casualty.
13. With one hand, the rescuer holds the rope below the
GRIGRI, close to the attachment sling. With the
other hand they take in the slack rope as they squat
down.
14. Once the casualty’s weight has been transferred to
the GOTCHA™ then their lanyard can be
disconnected.
15. The casualty can now be lowered as follows.
16. To lower the casualty the rescuer must take hold o
f
the rope that exits the GRIGRI, and this is used to
control the descent.
17. With the other hand releases the black handle on the
GRIGRI until the rope can be fed at a controllable
speed. This thus lowers the casualty.(Please see
note)
INSTALLATION & USE : INSTRUCTIONS
LOW
ANCHOR
Green Pulley to Anchor Sling
5
7
11-13
8
17
NOTE: In order to carry out a rescue the rescuer requires a harness with a front point of attachment for locating the GRIGRI.
If the anchor point for the GOTCHA™ is such that the casualty must be lowered, then the rope length in the kit must
be four times the distance from the anchorage to the point of safety.
Anchorage at foot level.
1. Access casualty’s anchorage point.
2. Attach the anchor sling to a suitable anchor point
above the casualty.
3. The rescuer will use their legs to help pull in the rope.
The single pulley is clipped to the anchor sling.
4. Adjust pole to the required length.
5. Attach the red clip to the end of the pole, and clip the
double pulley into the webbing.
6. Adjust ropes in-between the pulleys to the same
length as the pole.
7. Set the red clip to open.
8. Using the pole, attach the red clip to the casualty’s
harness attachment.
9. Remove the pole from the red clip.
10. Attach the GRIGRI to the rescuers harness.
11. Pull the slack rope through the GRIGRI to tension the
system, and squat down.
12. The rescuer now stands up, thus raising the casualty.
13. With one hand, the rescuer holds the rope below the
GRIGRI, close to the attachment sling. With the
other hand they take in the slack rope as they squat
down.
14. Once the casualty’s weight has been transferred to
the GOTCHA™ then their lanyard can be
disconnected.
15. The casualty can now be lowered as follows.
16. To lower the casualty the rescuer must take hold o
f
the rope that exits the GRIGRI, and this is used to
control the descent.
17. With the other hand releases the black handle on the
GRIGRI until the rope can be fed at a controllable
speed. This thus lowers the casualty.(Please see
note)
INSTALLATION & USE : INSTRUCTIONS
LOW
ANCHOR
Green Pulley to Anchor Sling
5
7
11-13
8
17
NOTE: In order to carry out a rescue the rescuer requires a harness with a front point of attachment for locating the GRIGRI.
If the anchor point for the GOTCHA™ is such that the casualty must be lowered, then the rope length in the kit must
be four times the distance from the anchorage to the point of safety.
Anchorage at foot level.
1. Access casualty’s anchorage point.
2. Attach the anchor sling to a suitable anchor point
above the casualty.
3. The rescuer will use their legs to help pull in the rope.
The single pulley is clipped to the anchor sling.
4. Adjust pole to the required length.
5. Attach the red clip to the end of the pole, and clip the
double pulley into the webbing.
6. Adjust ropes in-between the pulleys to the same
length as the pole.
7. Set the red clip to open.
8. Using the pole, attach the red clip to the casualty’s
harness attachment.
9. Remove the pole from the red clip.
10. Attach the GRIGRI to the rescuers harness.
11. Pull the slack rope through the GRIGRI to tension the
system, and squat down.
12. The rescuer now stands up, thus raising the casualty.
13. With one hand, the rescuer holds the rope below the
GRIGRI, close to the attachment sling. With the
other hand they take in the slack rope as they squat
down.
14. Once the casualty’s weight has been transferred to
the GOTCHA™ then their lanyard can be
disconnected.
15. The casualty can now be lowered as follows.
16. To lower the casualty the rescuer must take hold o
f
the rope that exits the GRIGRI, and this is used to
control the descent.
17. With the other hand releases the black handle on the
GRIGRI until the rope can be fed at a controllable
speed. This thus lowers the casualty.(Please see
note)
INSTALLATION & USE : INSTRUCTIONS
LOW
ANCHOR
Green Pulley to Anchor Sling
5
7
11-13
8
17
NOTE: In order to carry out a rescue the rescuer requires a harness with a front point of attachment for locating the GRIGRI.
If the anchor point for the GOTCHA™ is such that the casualty must be lowered, then the rope length in the kit must
be four times the distance from the anchorage to the point of safety.
Gotcha Reddingskit
15. Het slachtoffer kan nu als volgt worden neergelaten.
16. Om het slachtoffer te laten zakken, moet de
reddingswerker het touw vastnemen dat de GRIGRI verlaat,
en hiermee de neerlating regelen.
17. Met de andere hand ontgrendelt hij de zwarte handgreep
op de GRIGRI tot het touw met een regelbare snelheid kan
doorlopen. Op die manier gaat het slachtoffer omlaag.
(Zie opmerking)
OPMERKING: Om het reddingswerk uit te voeren,
moet de reddingwerker een harnas hebben met een
bevestigingspunt aan de voorzijde voor de GRIGRI. Als
het ankerpunt voor de GOTCHA™ dusdanig is dat het
slachtoffer moet worden neergelaten, moet het touw
in de kit vier keer zo lang zijn als de afstand tussen de
verankering en de veilige plek. Bewaar deze instructies
of een kopie ervan bij de GOTCHA™ voor latere
Inspecties En Onderzoek.
De uitrusting moet bij levering ter plaatse en vóór elk gebruik
visueel en voelbaar worden geïnspecteerd. SpanSet adviseert
dat de inspectie om de zes maanden wordt uitgevoerd en
geregistreerd door een bevoegde persoon.
Let vooral op het volgende:
Metalen onderdelen – Inspecteer deze op tekenen van
schade/vervorming/corrosie en de correcte werking en
vergrendeling van verbindingsstukken.
Touw* – Onderzoek touwen op tekenen van slijtage/afslijting,
ook slijtage tussen de strengen, uitrafeling, verlenging en
versmelting.
* In tegenstelling tot algemene slijtage kan plaatselijke
afschuring worden veroorzaakt doordat het touw over scherpe
randen of uitsteeksels loopt terwijl het onder spanning staat,
waardoor de sterkte van het touw drastisch kan verminderen.
Een lichte beschadiging van de buitenste vezels en enkele
losse draden kan als probleemloos worden beschouwd, maar
als de diameter van het touw kleiner is geworden of als het
mantelpatroon ernstig vervormd is, moet het touw worden
afgekeurd.
Alle persoonlijke beveiligingsmiddelen moeten onmiddellijk
uit gebruik worden genomen als ze heeft blootgestaan aan
schokken of als er twijfels zijn over de goede staat ervan. (Zie
lijst hierboven)
De GOTCHA™ kan indien gewenst worden gereinigd.
Volgende procedure moet worden opgevolgd: Gebruik een
mild reinigingsmiddel met handwarm water en een doek
of spons om de GOTCHA™ af te vegen. Zorg ervoor dat de
GOTCHA™ niet te nat wordt. Vervolgens moet deze procedure
worden herhaald met schoon water om te spoelen, waarna
de uitrusting op natuurlijke wijze moet drogen, op een veilige
afstand van directe warmtebronnen. Als u meer informatie wilt
hebben, kunt u contact opnemen met SpanSet.
Alle uitrusting moet als volgt worden bewaard en
getransporteerd:
- Vermijd contact met scherpe voorwerpen.
- Op een veilige afstand van schadelijke stoffen.
- Op een koele en droge plaats, weg van direct zonlicht.