How to fix Spartan Clean on the Go Dispenser when system does not dispense solution?
If your Spartan Dispenser system isn't dispensing solution, a common cause is a clogged water inlet strainer. Try cleaning the strainer, and if that doesn't work, replace it.
Why is my Spartan Clean on the Go A-gap spraying out and/or leaking?
If your Spartan Dispenser's A-gap is spraying or leaking, it could be due to limescale or dirt on the upper nozzle. Try soaking the nozzle in hot water with limescale remover to clean it. If the issue persists, consider replacing the nozzle. Another cause might be a venturi coated with limescale or dirt, which can be cleaned by soaking it in hot water and limescale remover, and replacing if necessary. Also, check for any buildup or clogs in the discharge hose and clean it to eliminate any restrictions. Ensure the discharge hose dispenses below the dispenser to prevent back pressure.
Why won't the water flow stop on my Spartan Dispenser?
If the water flow in your Spartan Dispenser won’t stop, it might be because the activation valve is clogged by minerals or other waterborne debris. Try soaking the valve parts and valve seat in limescale remover to clean them. If the problem continues, replace the parts.
Why does Spartan Clean on the Go Dispenser continue to draw chemical after the valve is closed?
If your Spartan Dispenser system continues to draw chemical after the valve is closed, it's likely because the chemical tank is positioned higher than the dispenser, causing siphoning. To resolve this, move the chemical container below the dispenser discharge point.
How to fix leaking activation valve on Spartan Dispenser?
If the activation valve on your Spartan Dispenser is leaking, make sure the valve cap is firmly hand-tightened until the leak stops. If the leak persists, reposition the valve or replace it if necessary.
What to do if connections and end cap are leaking on Spartan Dispenser?
If the connections and end cap on your Spartan Dispenser are leaking, it could be due to a missing o-ring in the connection fitting and/or end cap. Apply the o-ring, or replace the entire part if needed. Alternatively, the o-ring in the connections or end cap might be damaged. In this case, replace the o-rings or replace the entire end cap.
What causes F-gap back-flow preventer to leak on Spartan Clean on the Go Dispenser?
If the F-gap back-flow preventer is leaking on your Spartan Dispenser, it's likely that the flexible membrane is damaged. Replace the back-flow preventer to solve this issue.
What to do if Spartan Dispenser has improper concentration of chemical or no suction?
If your Spartan Dispenser is experiencing improper chemical concentration or no suction, one potential cause is insufficient water pressure. Ensure that the water pressure meets the minimum requirement of 15 PSI (1 bar), and check plumbing options if needed. Also, the metering tip could be clogged; try replacing it. Another possibility is a clogged foot valve, which can be resolved by soaking it in hot water and hand-cleaning or replacing it. Additionally, a clogged venturi or back-flow preventer can cause this issue, so soak them in hot water or limescale remover to clean, replacing if necessary. An air leak in the chemical pickup tubing line can also be the culprit, so check the entire line, replacing the tubing and checking the connections and cable tie. If the product is too thick, cha...
Details on water supply, connection type, flow rates, dimensions, working pressure, and temperature.
Crucial safety instructions for installation, including protective clothing and proper discharge.
Step-by-step guide for installing a single dispenser unit, including bracket attachment and hose connections.
Instructions for connecting and installing multiple dispenser units together, including bracket and unit connectors.
Guide on selecting the correct metering tip and connecting the product pickup tube to the dispenser.
Steps for cutting tubing, connecting the foot valve/filter, and attaching the ceramic weight.
Detailed procedure for calibrating the dispenser tips to achieve the desired product dilution ratio.
Information on hydraulic features, dilution ratios for different models, and required flow rates.
Identifies common problems like no solution dispensing, leaks, or incorrect concentration and provides solutions.
To Next Page
General