Speakman GRAVITYFLO SE-4400

To Next Page

INSTRUCTIONS FOR MODELS

92-SE-4400-R1

NEED HELP?

TOOLS AND SUPPLIES

IMPORTANT

SE-4400

GRAVITYFLO

Portable Eyewash

REQUIRED

ANSI Z358.1 requires that all self-contained eyewash

units shall be visually inspected weekly, unless the

product is placed in environments with extreme

conditions that may affect the form, fit, or function of

the unit (temperature, dirt, etc.). If this is the case, then

the inspection should be conducted more often as the

end user deems necessary. Speakman Company

furnishes a testing record tag (91-0635) with each unit.

On this tag, the date of inspection and the inspectors’

initials should be noted. ANSI Z358.1 specifies that the

height of the spray heads is to be between 33”-45”

from the floor. The SE-4400 weighs approximately 100

lbs when filled. Ensure the mounting surface and

mounting hardware (not supplied) can safely hold a

minimum vertical load of 150 lbs. Be sure to read

instructions thoroughly before beginning installation.

Do not overtighten any connections or damage may

occur. The unit should be full at all times, to achieve the

minimum 15 minute run time as stated by ANSI, in

case of an emergency. Refill the tank to full level after

each activation.

HELPFUL

SAFETY TIPS

MAINTENANCE

Be sure to always wear proper eye protection. Wear

proper skin protect on when cleaning and disinfecting

unit.

Occasional cleaning and disinfection is recommended.

To clean the inside of unit, add 1/4 cup (2 fluid oz.) of

Clorox Liquid Bleach to a full tank of potable water.

Allow the mixture to penetrate for 15 minutes. Drain

tank, and rinse thoroughly several times with potable

water. For further information about Clorox Liquid

Bleach, call toll-free at 1-800-292-2200. Follow

refilling instructions in this manual and place tank back

in service. Should any repair part be required, use only

genuine SPEAKMAN parts for repair or replacement.

See available replacement parts on the final page of

this manual. To order replacement parts, please call

toll-free at 1-800-537-2107

WARRANTY

Additional warranty information can be found at:

www.speakmancompany.com

For additional assistance or service please contact:

SPEAKMAN

Company

400 Anchor Mill Road

New Castle, DE 19720

800-537-2107

customerservice@speakmancompany.com

www.speakmancompany.com

Drill necessary holes into mounting surface and

secure Mounting Bracket to surface using

appropriate hardware, being sure to torque to

manufacturer’s specifications.

Select a suitable mounting location for the

SE-4400 capable of supporting 150 lbs. The

location should protect the unit from freezing

and potential scalding conditions. Place

mounting bracket on surface so the top of the

mounting bracket is located between 58

3/8”

from the floor. Making sure the bracket

is level, mark the mounting locations onto the

structure.

Pencil

Level

Drill Drill Bit

Measuring

Tape

Socket

Wrench

Deep Well

Socket

Safety

Glasses

Stud Finder

58-3/8” - 69-3/8”

1483mm - 1762mm

TO FLOOR

NOTE: Mounting hardware not included.

Ensure the mounting surface (wall, etc.) and

mounting hardware can safely hold a minimum

vertical load of 150 lbs.

Need help?

Do you have a question about the Speakman GRAVITYFLO SE-4400 and is the answer not in the manual?

Summary

Tools and Supplies

Required Tools

Lists essential tools like pencil, level, measuring tape, drill, socket wrench for eyewash installation.

Helpful Supplies

Lists optional but recommended items like safety glasses and a stud finder for safe usage.

Important Safety and Compliance Information

ANSI Z358.1 Requirements

Details weekly inspection, spray head height (33-45"), and load capacity (150 lbs) for eyewash units.

Safety Tips

Advises wearing proper eye and skin protection during cleaning and disinfecting procedures.

Maintenance Instructions

Provides guidance on cleaning the unit with a bleach solution and rinsing with potable water.

Warranty Information

Directs users to the Speakman Company website for additional warranty details.

Installation Guide

Select and Mark Mounting Location

Choose a location suitable for 150 lbs, between 58 3/8"-69 3/8" from the floor, and mark bracket positions.

Secure Mounting Bracket

Drill holes and firmly attach the mounting bracket to the surface using appropriate hardware.

Install and Fill Tank

Place the empty tank onto the bracket and fill with potable water to the designated line (approx. 9 gallons).

Secure Fill Cap and Maintenance Tag

Reinstall the fill cap, secure with the seal tie, and attach the maintenance tag to the tank.

Activate Water Flow

Rotate the activation tray downward to begin the flow of water from the eyewash.

Product Specifications and Support

Repair Part Groups

Lists available replacement parts with their respective part numbers and quantities.

Rough-in Dimensions

Provides detailed measurements and diagrams for the unit's physical installation.

Flow Data

Specifies the minimum run time (15 minutes) and flow rate (0.4 gpm) for the eyewash unit.

Need Help?

Contact Speakman Company for additional assistance or service via phone or email.