D=K6BCTU6G=B?T>@=?>B6>=>;6 D6BVU
U(*N;7*,8"83
W=G>?>Fh%BT%UG6!6>B%K?G6L%%
?K%=%K<=@@=X<6%DT<!6>B%>66AD%BT%X6%VD6AL%%
=AZ6G6%BT%BZ6%KT<<TW?>F-
a. K&77&)%#&7]*8$%5,8'2,4$'(*(_#%47*,8%'/%
"8#$('4$"&8#%,89%#,2*$E%/(*4,'$"&8#1
b. K7'#.%D/(,E%F'8%,%2'77%.&#*%
7*83$.%2(&5%,"(%4&5/(*##&(1
c. ?2%4&77*4$"83%27'#.*9%#&7]*8$#%"8%
5*$,7%4&8$,"8*(L%$(,8#2*(%$&%8&85*$,7%
4&8$,"8*(L%,89%27'#.%5*$,7%4&8$,"8*(1
d. W&(\%2,(%,),E%2(&5%,8E%"38"$"&8%
#&'(4*#%"8%,%],/&(%2(**%,(*,1
e. Y**/%47,##%=X;%2"(*%*a$"83'"#.*(%8*,(+E1
>TB?;6-%%A&%8&$%"55*(#*%D/(,E%F'8%X&9E%"8%#&7]*8$1%%A&%8&$%,77&)%#&7]*8$%$&%*8$*(%$.*%,"(%"87*$1
1. Designate a container for spent solvent.
2. Remove Cup’s Lid and add 2 - 4 ounces of
solvent-based cleaner (sold separately).
3. Replace Lid and pull out Air Vent to open.
>&$*- When Spray Gun is idle, push in Air Vent to close.
4. Open Fluid Control Knob and Fluid
Lock Nut (counterclockwise) until four threads
are showing. Turn Fluid Lock Nut clockwise
until it stops against the Spray Gun body.
5. Open Air Control Knob fully.
PSI
Bar
K7'"9%
;&8$(&7%
Y8&+
K7'"9%
<&4\%
>'$
6. Point Spray Gun at interior side of spent solvent
container. Depress Trigger and slightly shake
Spray Gun while spraying solvent into the container.
7. Disconnect Spray Gun from the air source.
8. After disconnecting, point the Spray Gun into
the spent solvent container and depress the
Trigger again to make sure no air remains.
9. Remove Regulator.
10. Remove Cup and Lid and allow to dry.
11. Turn Lock Ring counterclockwise by hand
to remove Air Cap and allow to dry.
12. Depress Trigger to open passageway, then blow
clean compressed air into the Fluid Inlet.
<&4\%
G"83
;&5/(*##*9%
="(
13. Reassemble Spray Gun.
>TB?;6- A&%8&$%'#*%,8E%\"89%&2%7'+("4,8$%
"8%,"(%#'//7E%&(%,"(%"87*$1%%B.*%7'+("4,8$%)"77%
5"a%)"$.%/,"8$L%4,'#"83%/&&(%(*#'7$#1
D/*8$%#&7]*8$%9"#/&#,7
After cleaning, dispose of spent solvent according to the solvent manufacturer’s
directions and local hazardous waste standards.
To Next Page
Loading...
Need help?
General