Standard Horizon RAM4 - User Manual

Front and Rear Panel
① Power/VOL knob
Press and hold this knob to turn the transceiver and the remote mic ON or OFF.
Adjusts the speaker volume level.
② DIAL/ENT knob
While the normal screen is displayed, rotate the DIAL/ENT knob to select your desired channel. While the MENU
screen is displayed, rotate the knob to select your desired menu item.
Secondary uSe
 Press this knob to enter a selection in the MENU.
③ SQL key
(
Squelch control
)
Press this key to activate the squelch adjustment mode. Press the CH▲ or CH▼ key to adjust the squelch level.
④ PTT
(
Push-To-Talk
)
switch
Push this switch to enable the transmitter.
②
①
③
④
⑤
⑥
⑦
⑧
⑨
⑩
⑪
⑫
⑦
⑬
⑭
⑮
⑯
SSM-70H
Remote Station Microphone RAM4
The RAM4
(
SSM-70H
)
allows you to remotely control all functions of the enabled Standard Horizon
xed mount VHF radio. The full dot matrix display and programmable keys make operation simple and
fast. Additional features include turning the radio ON/OFF and all DSC functions including Distress.
The RAM4
(
SSM-70H
)
can be extended up to 70 feet using the optional CT-100
(
23 feet
)
extension
cable. The RAM4
(
SSM-70H
)
is backed by an industry leading 3-years waterproof warranty.
Owner’s Manual
The details of the installation and operation of the RAM4
(
SSM-70H
)
is included in the owner’s
manual of the compatible xed mount radio, or it can be downloaded at www.standardhorizon.com.
⑤ CLEAR/ key
Press this key to cancel a menu selection. Press and hold this key to activate the key lock function.
Press and hold this key again to deactivate the key lock function.
⑥ Microphone
The internal microphone transmits your voice reducing background noise using Clear Voice Noise Reduction
Technology.
Note: Position your mouth about 1/2”
(
1.5 cm
)
away from the microphone hole and speak in a normal voice.
⑦ ◄/► key
Press these keys to switch the function of soft keys.
Secondary uSe
While the MENU screen is displayed, press the key to slide the on-screen menu to the right/left side.
⑧ MENU key
Press this key to access the MENU.
⑨ CH▼/CH▲ key
These keys are used to change the operating channel.
Press the key momentarily, the channel increases/decreases one step. Holding the key, the channel increases/
decreases continuously.
Secondary uSe
 While the MENU screen is displayed, press the key to slide the on-screen menu upward/downward.
⑩ Display
Full dot matrix display, 222 by 162 pixels.
⑪ Soft keys
These three programmable keys can be customized in the setup menu to quickly access advanced functions of the radio.
⑫ Strobe Light
When the [STROBE] soft key is pressed, the internationally-recognized Morse Code “S.O.S” message will light and
ash repeatedly.
From MENU → SETUP → CONFIGURATION → STROBE LED, you can select one option from “CONTINUOUS”,
“SOS”, “BLINK 1”, “BLINK 2” and “BLINK 3”.
⑬ 16/S key
Pressing this key immediately recalls channel 16 from any channel location. Holding down this key recalls the SUB
channel
(
The default setting is channel 9
)
. Pressing this key again reverts to the previous selected working channel.
⑭ Speaker
The internal speaker is located here.
⑮ DATA jack
Use the micro USB type B jack for RAM4
(
SSM-70H
)
rmware updates.
Note: When the DATA jack is securely covered with rubber cap, the SSM-70H meets the waterproong performance.
⑯
DISTRESS
key
This key is used to send a DSC distress call.
Included Accessories and replacement part numbers
(
1
)
23 Feet Routing Cable
(
S8101512
)
(
2
)
Rubber Cap
(
RA052520A
)
(
3
)
Mounting Bracket
(
RA052510A
)
& Screws
(
U24312020 x 4 pcs
)
(
4
)
Microphone Hanger
(
RA0458800
)
& Screws
(
U40412220 x 2 pcs
)
(
5
)
Ferrite Cores
(
L9190212 x 2 pcs
)
(
6
)
Operating Manual
Optional Accessories
(
1
)
CT-100 23 Feet Extension Cable
(
2
)
MLS-300 External Loud Speaker
(
3
)
MLS-310 10W Amplied External Speaker
(
1
)
(
2
)
(
3
) (
4
) (
5
)

Standard Horizon RAM4 Specifications