Stanley 6-GR25 - STANLEY Glue Gun 6-GR25; Technical Data; Safety Instructions; Electrical Safety

1
ENGLISH
OPERATING INSTRUCTIONS
IMPORTANT: Please read carefully before using your electric
gluegun.
1. Plug your glue gun into an electricaloutlet.
2. To open the fold-away-stand, take hold of the flanges on
both sides of the stand and pull forward until the stand locks
intoposition.
3. The Stanley® Dualmelt™ Glue gun allows you to work on the
high setting for general purpose use and the low setting for
heat sensitive materials. High-low switch is located in center
front of handle. Move switch to desired temperature setting.
High temperature is for bonding wood, leather, ceramics
and other non-porous materials. Low temperature is
for bonding paper, fabric, dried flowers and other heat
Applications and Repairs
• Woodworking
• Plastics
• Foam
• Fabrics
• Paper
• Cardboard
• Crevices
• Repair book bindings, shoe or loosecarpeting.
• Sealing windows, tiles, and bathroom fixtures
• Dried floral arrangements
• Electrical insulation

CAUTION: Read Safety Rules and Operating
InstructionsCarefully.

WARNING: When using electric tools, basic safety
precautions should always be followed to reduce the risk
of fire, electrical shock and personalinjury.
READ ALL SAFETY INSTRUCTIONS:
1. Do not touch the nozzle area or meltedglue.
2. Keep work area clean. Work environment should be clean,
dry well lit and clear of flammablematerials.
3. Guard against electric shock. Prevent body contact with
grounded surfaces like pipes and appliances. Do not use
nearwater.
4. Inspect extensioncords.
5. Keep childrenaway.
6. Always use safetyglasses.
7. Don’t abuse cord. Never carry the tool by the cord or yank
the cord to disconnect from plug orreceptacle.
8. Disconnect tools when not inuse.
9. Avoid accidental glue discharge. Do not touch the glue stick
or trigger except to dispenseglue.
10. To reduce the risk of fire or electric shock, do not expose this
product to rain ormoisture.
11. When not in use, the tool should be storedindoors.
12. Do not pull glue sticks from gun. The feed mechanism may
become damaged or impaired. If you desire to change types
of glue, cut off protruding end and feed the remainder
through with the new type ofglue.

CAUTION: WHEN GUN IS HOT DO NOT LAY IT ON ITS
SIDE. ALWAYS USE STAND. MELTED GLUE WILL BURN
SKIN. OPERATING TEMPERATURE OF THE NOZZLE IS
380° F (193°C). DO NOT TOUCH THE NOZZLE AREA OR
MELTEDGLUE.
Electrical Safety
Double insulated tools are equipped with a polarized plug (one
blade is wider than the other). This plug will fit in a polarized
outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified
electrician to install a polarized outlet. Do not change the plug
in any way. Double insulation eliminates the need for the three
wire grounded power cord and grounded power supplysystem.
Safety Precautions:
• Do not touch nozzle area of glue gun or meltedglue.
• Do not make repairs to the gluegun.
• Do not use a damaged gluegun.
• Do not allow glue gun to come in contact with water,
liquids orrain.
• Do not carry the tool by the cord or pull cord to disconnect
it from theoutlet.
• For interior useonly.
• Do not leave the glue gun unattended duringuse.
• Do not attempt to remove unused glue from the glue gun
afteruse.
• Place the glue gun in the upright position when idle using
the fold down standprovided.
• Do not use this product in areas where the risk of explosion
ispresent.
• If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similar qualified persons in
order to avoid ahazard.
6-GR25
Input V
AC
230
Frequency Hz 50
Power W 30
English (original instructions)
Congratulations!
You have chosen a STANLEY tool. Years of experience, thorough
product development and innovation make STANLEY one of the
most reliable partners for professional power toolusers.
Technical Data
GLUE GUN
6-GR25