Stanley ST-175T-KFA-E User Manual

Stanley ST-175T-KFA-E

65 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

ST-45-KFA-E / ST-70T-KFA-E /ST-70TW-KFA-E /

ST-125T-KFA-E / ST-175T-KFA-E / ST-215T-KFA-E

NEVER LEAVE HEATER UNATTENDED WHILE BURNING, OR WHILE

CONNECTED TO A POWER SOURCE.

THIS PRODUCT IS NOT SUITABLE FOR PRIMARY HEATING PURPOSES.

STKB-430

Other manuals for Stanley ST-175T-KFA-E

Operating Instructions89 pages

User Manual12 pages

Instruction Manual85 pages

Questions and Answers:

T
Timothy MooreAug 21, 2025
What to do if Stanley ST-175T-KFA-E won't operate and shows error E1?
- A
  amandabushAug 21, 2025
  If your Stanley Heater won't operate, or the motor runs briefly, and the LED display shows “E1”, there are several potential causes. First, ensure the fuel tank has fresh paraffin. Second, the pump pressure may be incorrect and needs adjustment. Third, the spark plug might be corroded or have an incorrect gap, requiring cleaning or replacement. Fourth, the fuel filter or nozzle may be dirty and need cleaning or replacement. Fifth, there might be moisture in the fuel or fuel tank, in which case you should rinse out the fuel tank with clean, fresh paraffin. Sixth, inspect all electrical connections. Finally, the ignitor wire may not be connected to the spark plug, or the ignitor itself may be defective, requiring re-attachment or replacement.
T
Tyler WardAug 23, 2025
What to do if Stanley Heater shuts off after short time and shows “E1”?
- W
  wendy78Aug 23, 2025
  If your Stanley Heater fires up but the Main PCB shuts it down quickly, and the lamp flickers with an “E1” error on the LED, it could be due to several reasons: * Incorrect pump pressure: Adjust the pump pressure. * Dirty filters: Clean or replace the air filter, fuel filter, or nozzle. * Dirty photocell lens: Clean or replace the photocell. * Photocell issues: Adjust the photocell position, replace it if defective, or check the wiring between the Main PCB and photocell.
C
Corey TurnerAug 26, 2025
Why Stanley ST-175T-KFA-E won't operate and shows “E1”?
- T
  tgillAug 26, 2025
  If your Stanley Heater isn't operating, or the motor runs briefly, the lamp flickers, and the LED displays “E1”, possible causes include: 1. Empty fuel tank: Refill with fresh paraffin. 2. Incorrect pump pressure: Adjust the pump pressure. 3. Spark plug issues: Clean or replace a corroded spark plug. 4. Dirty filters: Clean or replace the fuel filter or nozzle. 5. Fuel contamination: Rinse the fuel tank with clean, fresh paraffin. 6. Wiring: Inspect all electrical connections, re-attach ignitor wire to spark plug or replace the ignitor.
K
Kelly RojasAug 27, 2025
What to do if my Stanley ST-175T-KFA-E Heater does not turn on?
- A
  Andrea JohnsonAug 28, 2025
  If your Stanley Heater won't turn on and the lamp isn't lit, there are several things you can check. First, the temperature limit sensor may have overheated; turn the power switch off, let the heater cool for 10 minutes, then turn it back on. Next, ensure the heater is properly connected to a power source and that the power supply is working. Also, inspect the fuse and replace it if necessary. Finally, check all electrical connections between the temperature limit sensor and the circuit board.
E
Elizabeth MerrittAug 30, 2025
Why is the fan not working on my Stanley ST-175T-KFA-E Heater?
- A
  Andrea BensonAug 30, 2025
  If your Stanley Heater fan isn't working when plugged in and switched on, and the LED display shows “E1” or “E2”, it could be due to the thermostat being set too low (though this doesn't apply to the ST-45-KFA-E model). Try rotating the thermostat to a higher setting. Additionally, there may be a broken electrical connection between the Main PCB and the motor; inspect all electrical connections.
M
Molly BurnsSep 1, 2025
What does error code E3 mean on Stanley ST-175T-KFA-E Heater?
- Z
  Zachary GlassSep 1, 2025
  If the LED display on your Stanley Heater shows “E3”, it indicates that the thermostat switch has failed and needs to be replaced.
Y
yeseniacarterSep 3, 2025
How to fix poor combustion in Stanley ST-175T-KFA-E?
- J
  James RodriguezSep 3, 2025
  If your Stanley Heater has poor combustion and/or excess soot production, several factors could be responsible. First, the input, output, or lint filter might be dirty and need cleaning or replacement. Second, the fuel filter may be dirty and also require cleaning or replacement. Third, the fuel quality could be poor, so ensure the fuel is not contaminated or old. Finally, the PSI might be too high or too low; make sure to use the proper pressure.
S
Stephen ReyesSep 5, 2025
Why Stanley ST-175T-KFA-E Heater shows E1 and won't operate?
- J
  Joel SimmonsSep 5, 2025
  If your Stanley Heater displays 'E1' and isn't operating correctly, it could be due to several reasons: * The fuel tank might be empty; refill it with fresh paraffin. * The pump pressure could be incorrect; adjust it accordingly. * The spark plug might be corroded or have an incorrect gap; clean or replace it. * The fuel filter or nozzle could be dirty; clean or replace them. * There might be moisture in the fuel tank; rinse it with clean paraffin. * Check the ignitor wire if it's not connected to the spark plug and re-attach it. * Check all electrical connections, and replace the ignitor if it's defective.
D
Diana PadillaSep 7, 2025
What to do if Stanley ST-175T-KFA-E Heater fires then shuts off with E1 error?
- K
  Kristi DeanSep 7, 2025
  If your Stanley Heater starts but then shuts off, displaying an 'E1' error, it could be due to several issues. First, the pump pressure might be incorrect, so adjust it. Also, the input, output, or lint filter, as well as the fuel filter or nozzle, could be dirty. Clean or replace these filters and the nozzle. The photocell lens might also be dirty or improperly installed; clean or adjust its position. If the photocell is defective, replace it. Finally, check the electrical connection between the Main PCB and the Photocell.
C
caitlin12Sep 9, 2025
What to do if Stanley ST-175T-KFA-E won't turn on?
- K
  Karen HunterSep 9, 2025
  If your Stanley Heater doesn't turn on and the lamp isn't lit, the temperature limit sensor may have overheated; turn the power switch off and let the heater cool for 10 minutes before turning it back on. Check the power cord and extension cord to ensure a proper connection and test the power supply. Also, the fuse might be blown, so check and replace it if necessary. Inspect all electrical connections between the Temperature Limit Sensor and the Circuit Board.

Stanley ST-175T-KFA-E Specifications

General

BTU	175, 000 BTU
Fuel Type	Kerosene
Oscillation	No
Thermostat	Yes
Heater Type	Forced Air
Safety Features	Overheat Protection
Color	Black

Related product manuals

Preview: Stanley ST-125-OFR-E

Stanley ST-125-OFR-E

Preview: Stanley ST-70-SS-E

Stanley ST-70-SS-E

Preview: Stanley ST-22-240-E

Stanley ST-22-240-E

Preview: Stanley ST-23-240-E

Stanley ST-23-240-E

Preview: Stanley ST-45-KFA-E

Stanley ST-45-KFA-E

Preview: Stanley ST-70T-SS-E

Stanley ST-70T-SS-E

Preview: Stanley ST-70T-KFA-E

Stanley ST-70T-KFA-E

Preview: Stanley ST-222A-240-E

Stanley ST-222A-240-E

Preview: Stanley ST-70TW-KFA-E

Stanley ST-70TW-KFA-E

Preview: Stanley ST-221A-240-E

Stanley ST-221A-240-E

Preview: Stanley stn17g

Preview: Stanley ST125T-KFA-E

Stanley ST125T-KFA-E