S96, S66
Bluetooth transceiver
GSM antenna
X1
X2
X3
X4
X6
Valet button with LED
Temperature sensor
USB connector
For convenient setup, diagnostics and software upgrade use the free StarLine Master
software available at help.starline.ru/slm/en
Login into the program with a service code in the owner’s plastic card.
Mounting recommendations
Mount the main unit at a distance not less 10 cm from the
metal surfaces, to avoid Bluetooth and GSM signal
transmission interference.
For the cars equipped with CAN/LIN bus make a connection via the embedded digital CAN/LIN interface,
for the elder cars make an analogue connection.
Find information and wiring tips on vehicles and features supported with CAN/LIN connection at can.starline.ru
Security – telematic system
connection diagram
GPS+GLONASS receiver
X5
General installation requirements
The security system is designed for installation on vehicles with 12V on board voltage.
Prior to installation, make sure that the vehicle equipment circuits, to which the system is connected, are in suitable operating condition and no any trouble codes and check engine are indicated.
The system installation should be carried out according to the connection diagram.
The "ground" wire of the main unit should be connected rst to a car body ground with an original screw.
Mount the wiring far from sources of electrical interference: ignition coils, high-voltage wires, etc.
Make sure that the harness is not lay in contact with the moving parts of the vehicle: pedals, steering shaft etc.
Connect all the harness to the main unit sockets only after all wires mounting is complete.
Do no t the engine temperature sensor near the exhaust manifold, otherwise it may cause sensor overheating and damage.
Only the qualied and trained tter may carry out the security system installation.
The congured parameters of the security systems must comply with a vehicle manual instruction requirements.
30 А
+ 12 V
LIN1
Door opening simulation output (200 mA) (–)
CAN-L B
Engine blocking (200 mA) (–)
LIN2
“Comfort” function output (200 mA) (–)
CAN-L A
Engine operation monitoring input
Ignition input (+)
CAN-H A
Bypass module control output (200 mA) (–)
Parking brake input (–)
StarLine Bus core bus
Control output for code relay StarLine R4 (200 mA) (–)
DVR control output (2А) (+)
Trunk limit switch input (–)
Horn control output (2 A) (+)
Brake pedal input
Trunk unlocking output (200 mA) (–)
Door input (+/–)
Door two-step unlocking output (200 mA) (–)
Hood limit switch input (–)
Unit power supply
Storage battery
3 А
orange-black
green-black
brown-white
blue-black
brown
white
orange
gray
orange-white
white-black
red
orange
yellow
black-yellow
blue
green
CAN-H B
Security status output (200 mA) (–)
X2
Output to alternative light signal control (200 mA) (–)
Output to alternative central lock control (200 mA) (–)
Output to accessories (200 мА) (–)
Output to starter (200 мА) (–)
Output to ignition 1 (200 мА) (–)
Output to ignition 2 (200 мА) (–)
Output +12В (500 мА) (+)
Autostart connection diagram for S96
+12 V
Ignition lock
Starter
Ignition 1
Ignition 2
Power module
To connector
X2
To the yellow
wire of
connector X1
Accessories
+12 V
StarLine BP-03, BP-05
1 А
+12 V
StarLine BP-06
orange-violet
orange-white
blue-red
pink
yellow
gray-black
green-yellow
black-red
yellow-white
black-white
black
red
gray
green
orange-gray
yellow-red
blue-black
yellow-black
blue
X1
violet-yellow
not used
Common
Blocking relay
in the set
86
30
85
87
87а
NC
NO
Ignition 1
(–)
(+)
Variant 1
Variant 2
10 А
Activators are
connected in parallel
86
30
85
87
87а
86
30
85
87
87а
+12 V
(–)
(+)
(–)
(+)
command
«Close»
command
«Open»
Control output of the built-in starter lock (200 мА) (–)
yellow-orange violet
or
or
The manufacturer StarLine ScPA LLC reserves the right to make technical improvements
not shown in this diagram.
Information on firmware updates, actual versions of operation and installation manuals are
available at help.starline.ru.
Check other available
connection options at
help.starline.ru
To Next Page
Need help?
General
