StartingLine SB-2-610-G User Manual

Service Bulletin
SB-2-610-G
Replaces SB-2-610-F
ATTENTION !
LIRE AVANT DE FIXER LE TUYAU D’ARRIVÉE D’AIR
HVLP AIR SUPPLY REQUIREMENTS
EXIGENCES HVLP CONCERNANT L’ALIMENTATION EN AIR
PISTOLET Á PEINTURE: Une pression à l'admission de
2,07 BAR (30 PSI) donne une pression de 0,69 BAR (10 PSI)
à l’anneau déflecteur. Utilise 0,37 m
3
(13 pi
3
) à la minute.
REMARQUE : UTILISER UN TUYAU D’UN DIAMÈTRE INTÉRIEUR DE 7,94 MM (5/16 PO) AU MINIMUM.
PISTOLET DE RETOUCHE: Une pression à l'admission de
2,07 BAR (30 PSI) donne une pression de 0,69 BAR (10 PSI)
à l’anneau déflecteur. Utilise 0,23 m
3
(8 pi
3
) à la minute.
ATTENTION!
READ BEFORE ATTACHING THE AIR HOSE
HVLP AIR SUPPLY REQUIREMENTS
FULL SIZE GUN: 30 PSI inlet pressure provides 10 PSI at the air cap. Consumes 13 CFM.
TOUCHUP GUN: 30 PSI inlet pressure provides 10 PSI at the air cap. Consumes 8 CFM.
NOTE: USE 5/16" OR LARGER I.D. AIR HOSES
¡ATENCIÓN!
LEA ANTES DE FIJAR LA MANGUERA DE AIRE
REQUISITOS DE SUMINISTRO DE AIRE DE ALTO VOLUMEN BAJA PRESIÓN (HVLP)
PISTOLA HVLP: Una presión de entrada de 30 PSI (libras
por pulgada cuadrada) proporciona 10 PSI en la boquilla.
Consume 13 CFM (pies cúbicos por minuto).
NOTA: UTILICE MANGUERAS CON DIÁMETRO INTERNO DE 7.94 MM (5/16 DE PULG.) O MÁS GRANDE
PISTOLA RE-TOQUE: Una presión de entrada de 30 PSI (libras
por pulgada cuadrada) proporciona 10 PSI en la boquilla.
Consume 8 CFM (pies cúbicos por minuto).

StartingLine SB-2-610-G Specifications

General

Brand	StartingLine
Model	SB-2-610-G
Category	Paint Sprayer
Language	English

Summary

ATTENTION! READ BEFORE ATTACHING THE AIR HOSE

HVLP AIR SUPPLY REQUIREMENTS

Specifies inlet pressure, air cap pressure, and CFM for full size and touchup HVLP spray guns.

SET-UP AND ADJUSTMENT INSTRUCTIONS

Gun Setup and Adjustment Steps

Covers attaching the cup, flushing, setting controls, and attaching the air hose for spray gun setup.

PACKING ADJUSTMENT INSTRUCTIONS

Details how to adjust the packing nut for proper fluid needle movement.

WARNING

Potential Hazards and Safety Precautions

Outlines hazards like fire, solvent spray, toxic substances, and cumulative trauma disorders with corresponding safeguards.

CLEANING

Routine and Thorough Cleaning Procedures

Provides instructions for cleaning the spray gun, cup, and fluid tip and nozzle.

PREVENTIVE MAINTENANCE

Spray Gun Lubrication Points

Specifies lubrication points for trigger, air valve stem, fluid needle, and threads for optimal performance.

WARNING

Hazards During Equipment Use and Safeguards

Details fire, solvent spray, toxic substances, explosion, general safety, and CTD hazards with necessary precautions.

ACCESSORY ITEMS

Spray Gun Parts and Accessories

Lists and identifies various spray gun parts, O-rings, gaskets, and accessory cups with part numbers.