SteamSpa 7.5KW - User Manual

Questions and Answers

C
Crystal LeeAug 14, 2025
Why is there no steam when starting my SteamSpa 7.5KW Inverter?
- J
  jordan02Aug 14, 2025
  If your SteamSpa Inverter isn't producing steam, there could be several reasons: * There may be no electricity. Check the power supply and connections. * There may be no water. Check the water input pipe and water input valve. * The set temperature might be too low. Try resetting the temperature. * There could be a wiring connection problem. Inspect the wiring connections and tighten them if necessary.
A
ashley51Aug 17, 2025
What to do if my SteamSpa 7.5KW does not start when powered on?
- M
  Marisa Smith MDAug 17, 2025
  If your SteamSpa Inverter fails to start when powered on, consider the following possibilities: * A fuse may be burned out. Replace the fuse with one rated at 0.8A/240V. * The electrical wiring might have become loose. Cut the power supply and then reconnect the wiring. * The control panel connection could be loose. Reconnect the control panel and reset the Inverter. * Try turning the controller off and on.
M
Mathew RoblesAug 21, 2025
How to fix water leakage from my SteamSpa 7.5KW Inverter?
- N
  nathan73Aug 21, 2025
  If you notice water leaking from your SteamSpa Inverter, check these potential causes: * The water pipe connector may be loose, or the pipe itself might be broken. Tighten any loose connections or replace the broken pipe. * There could be a water leakage in the water input valve or the water drainage valve. Replace the water input valve or the water drainage valve.
C
Corey CookAug 25, 2025
What to do if the display screen on my SteamSpa Inverter control panel is blank?
- D
  Damon BlairAug 26, 2025
  If the display screen on your SteamSpa Inverter control panel remains blank, check the following: * Ensure the control panel wire is properly connected. Verify that the connection plug between the control panel and the generator is secure and that the power circuitry has good contact. * There might be an issue with the generator motherboard. In this case, replace the motherboard.
V
Virginia BernardAug 29, 2025
Why are the breakers tripping when I use my SteamSpa 7.5KW?
- K
  kelly32Aug 29, 2025
  If the breakers are tripping when you use your SteamSpa Inverter, here are a couple of things to investigate: * The wire connector may be dampened or damaged. Check the wire connector for dampness or damage, and dry it if it's dampened. * The heating element might be damaged. If so, replace the heating element.
P
Patricia ManningSep 1, 2025
How to troubleshoot if the light on my SteamSpa Inverter doesn't turn on?
- A
  alanlevineSep 1, 2025
  If the light on your SteamSpa Inverter isn't turning on, consider these possibilities: * The LED light bulb may be bad. Replace the LED light bulb. * The wiring connection may be improperly connected, or the light cable may be damaged. Tighten the connection or replace the light cable.
B
Bobby CostaSep 4, 2025
What to do if my SteamSpa 7.5KW Inverter produces hot water with little or no steam?
- D
  Deanna Sanchez MDSep 5, 2025
  If your SteamSpa Inverter is producing hot water with little or no steam, it could be due to a bad water drainage valve. Replace the water drainage valve.
R
richardrobertsSep 9, 2025
What should I do if the SteamSpa 7.5KW makes water sounds but produces no steam?
- R
  Rebecca TaylorSep 9, 2025
  If your SteamSpa Inverter makes water sounds but doesn't produce steam, a possible cause is a steam pipe blockage. Cut the power supply and check for any blockage in the steam pipe.