SteamSpa Oasis OA750CH

Questions and Answers

C
Christy HughesAug 19, 2025
What to do if there is no steam when starting my SteamSpa Oasis OA750CH?
- B
  Bruce ParrishAug 19, 2025
  If your SteamSpa Plumbing Product isn't producing steam, several factors could be at play. First, ensure the unit is receiving power and that all connections are secure. Next, verify that the water supply is connected and the water inlet valve is functioning correctly. Confirm that the set temperature isn't too low, and if necessary, adjust it. Lastly, inspect all wiring connections and tighten any loose connections.
J
jperryAug 21, 2025
Why are the breakers tripping with my SteamSpa Oasis OA750CH?
- J
  Jon JohnsonAug 21, 2025
  If the breakers are tripping when you use your SteamSpa Plumbing Product, it could be due to a dampened or damaged wire connector. Check the wire connector and dry it if it's damp. Another potential cause is a damaged heating element, which would need to be replaced.
M
Matthew ClarkAug 25, 2025
How to fix water leakage in SteamSpa Oasis OA750CH?
- J
  Joshua RodriguezAug 25, 2025
  If you notice water leakage in your SteamSpa Plumbing Product, start by checking all water pipe connectors to ensure they are tightened properly. If a pipe is broken, it will need to be replaced. Also, inspect the water input valve and the water drainage valve for leaks; if either is leaking, it should be replaced.
R
Rebecca DavisAug 26, 2025
What to do if my SteamSpa Plumbing Product does not start when powered?
- K
  Kevin HallAug 26, 2025
  If your SteamSpa Plumbing Product isn't starting when powered on, there are a few things to check. First, inspect the fuse and replace it if it's burned out (0.8A/240V). Next, ensure that the electrical wiring is securely connected. Also, check the control panel connection and reconnect it, then reset the system. Finally, try turning the controller off and on.
L
Larry BishopAug 28, 2025
Why does the display screen on my SteamSpa Plumbing Product control panel not display anything?
- S
  Scott SmithAug 28, 2025
  If the display screen on your SteamSpa Plumbing Product control panel is blank, first check the connection plug between the control panel and the generator to ensure it's secure and that the power circuitry has good contact. If the connection is good, the issue might be with the generator motherboard, which would need to be replaced.
C
chad81Aug 30, 2025
How to fix the light if it doesn't turn on in SteamSpa Plumbing Product?
- J
  Joshua DiazAug 30, 2025
  If the light in your SteamSpa Plumbing Product isn't turning on, the first step is to replace the LED light bulb. If replacing the bulb doesn't solve the problem, check the wiring connection to ensure it's properly connected. Also, inspect the light cable for any damage and replace it if necessary, while making sure the connection is tight.
C
Christine LandrySep 2, 2025
What to do if I'm receiving an error 'E0' on the SteamSpa Oasis OA750CH Plumbing Product control panel?
- R
  richard80Sep 2, 2025
  If you see an 'E0' error on your SteamSpa Plumbing Product control panel, it indicates a lack of water in the tank, possibly due to a jammed water inlet valve or a loose connecting cable. Try cleaning the water inlet valve by switching it on and off a few times to dislodge any buildup. Check the cable and make sure it is firmly connected. If the problem persists, you may need to replace the water inlet valve or the PC board.
K
Katie KingSep 4, 2025
What to do if hot water comes out with little or no steam from SteamSpa Oasis OA750CH?
- K
  Kevin HarrisSep 4, 2025
  If your SteamSpa Plumbing Product is dispensing hot water with little to no steam when started, the issue might be a bad water drainage valve. Consider replacing the water drainage valve to resolve this problem.
J
john76Sep 6, 2025
Why does the control panel of my SteamSpa Oasis OA750CH Plumbing Product show the temperature but not turn on?
- H
  hbeckSep 6, 2025
  If the control panel of your SteamSpa Plumbing Product displays the temperature but doesn't activate the unit, the water level sensor cable or the cable from the relay to the element may be loose. Ensure all cables to the heating elements are well connected. If the issue persists, the heating element might be malfunctioning and require replacement.
C
Christina GallowaySep 8, 2025
Why is cold water coming from the steam head of my SteamSpa Plumbing Product?
- L
  Laura HardinSep 8, 2025
  If cold water is coming from the steam head of your SteamSpa Plumbing Product, first check the water sensor cable to ensure it's securely connected. If the cable is well-connected, the water level sensor may be defective and need replacement. If the problem continues, the main PC board may be defective and require replacement.

Summary

Product Registration

Warranty Registration Methods

Details on how to register the product warranty either online or by mail.

Warranty Terms and Conditions

Conditions That Void the Warranty

Lists specific requirements and actions that will nullify the product warranty.

Safety Precautions and Warnings

General Safety Guidelines

Key instructions for safe installation and operation, including warnings for specific user groups.

Hyperthermia Risks and Prevention

Explains the causes, symptoms, and effects of hyperthermia and precautions.

Specific Hazard Warnings

Details on reducing risks of overheating, scalding, slipping, and falling.

User Instructions and Guidelines

Choosing the Right Location

Guidance on selecting an optimal installation site for the steam generator unit.

SteamSpa Oasis OA750CH Specifications

General

Product Type	Steam Generator
Model Number	OA750CH
Brand	SteamSpa
Power	7.5 kW
Voltage	240 V
Tank Capacity	1.5 Gallons
Control Type	Digital
Material	Stainless Steel
Weight	25 lbs
Phase	Single Phase
Heating Time	15 minutes

SteamSpa Oasis OA750CH - User Manual

Table of Contents