Steelcraft 70280B - User Manual

To Next Page

3” BULL BAR

2006-2010 HUMMER H3

Page 1 of 2 Rev1 (DP) 3/20/14

PARTS LIST:

Bull Bar

8-1.25mm x 30mm Hex Bolts

Driver/Left Mounting Bracket

8mm x 16mm x 1.6mm flat washers

Passenger/Right Mounting Bracket

8mm Nylon Lock Nuts

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ

INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.

2. NOTE: It may be necessary to remove/relocate front license plate and license plate bracket. It

is not required, but strongly recommended. If local/state law requires a license plate, license

plate relocation kit is available.

3. Start installation at the driver side front of the vehicle. Remove the tow hook loop from the

bracket. Leave the tow hook bracket in place. NOTE: Tow hook loops may be reinstalled once

Bull Bar Brackets are in place but it is not recommended.

4. Remove the (2) factory hex bolts attaching the tow hook bracket to the bumper. Do not remove

the bracket. Select the driver side Bull Bar Mounting Bracket. Bolt the Bull Bar Bracket to the

tow hook mounting bracket using the factory hex bolts.

5. Repeat Steps 3—4 to install the passenger side Bull Bar Bracket.

6. With help, position the Bull Bar onto the outside of the (2) Mounting Brackets. Attach the Bull

Bar to the Brackets with the included (4) 8mm x 30mm Hex Bolts, (8) 8mm Flat Washers, (4)

8mm Nylon Lock Nuts.

7. Level and adjust the Bull Bar and tighten all hardware at this time.

8. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

To protect your investment, wax this product after installing. Regular waxing is recommended to

add a protective layer over the finish. Do not use any type of polish or wax that may contain

abrasives that could damage the finish.

For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the

finish. Mild soap may be used also to clean the Bull Bar.

For gloss black finishes: Mild soap may be used to clean the Bull Bar.

Passenger/Right Side

Mounting Bracket

Driver/Left Side

Mounting Bracket

Need help?

Do you have a question about the Steelcraft 70280B and is the answer not in the manual?

This document provides installation instructions and maintenance guidelines for a 3" Bull Bar designed for the 2006-2010 Hummer H3.

Function Description:

The 3" Bull Bar is an accessory designed to be mounted on the front of a Hummer H3. While the primary function of a bull bar is often for aesthetic enhancement and minor front-end protection, this document focuses on its installation and maintenance rather than specific protective capabilities. It integrates with the vehicle's existing tow hook mounts, suggesting a robust attachment point.

Important Technical Specifications:

Compatibility: Specifically designed for the 2006-2010 Hummer H3.
Components (Parts List):
- 1 Bull Bar
- 1 Driver/Left Mounting Bracket
- 1 Passenger/Right Mounting Bracket
- 4 8-1.25mm x 30mm Hex Bolts (for attaching the bull bar to the mounting brackets)
- 8 8mm x 16mm x 1.6mm flat washers (for attaching the bull bar to the mounting brackets)
- 4 8mm Nylon Lock Nuts (for attaching the bull bar to the mounting brackets)
Mounting Hardware (Reused from Vehicle): The installation process reuses existing factory hex bolts that attach the tow hook bracket to the bumper, as well as factory tow hook mounting bolts.
Dimensions: The bull bar itself is described as a 3" diameter bar, though specific length or other dimensions are not provided.
Material (Implied): The maintenance section refers to "stainless steel" and "gloss black finishes," indicating that the bull bar is available in these material/finish options.

Usage Features (Installation Process):

The installation is a multi-step process that requires basic mechanical skills and tools (not specified, but implied for bolt removal and tightening).

Preparation:
- Unpack and verify all parts against the provided list.
- Read instructions thoroughly before beginning.
- License Plate Consideration: It may be necessary to remove or relocate the front license plate and its bracket. While not strictly required, it is strongly recommended. A license plate relocation kit is available if local/state law mandates a front license plate.
Driver Side Installation:
- Begin installation on the driver's side front of the vehicle.
- Remove the tow hook loop from its bracket, but leave the tow hook bracket in place.
- Note: Tow hook loops can be reinstalled after the Bull Bar Brackets are in place, but this is not recommended by the manufacturer.
- Remove the two factory hex bolts that secure the tow hook bracket to the bumper. Do not remove the tow hook bracket itself.
- Select the driver side Bull Bar Mounting Bracket.
- Bolt the Bull Bar Bracket to the tow hook mounting bracket using the original factory hex bolts that were just removed.
Passenger Side Installation:
- Repeat steps 3-4 for the passenger side of the vehicle to install the passenger side Bull Bar Bracket.
Bull Bar Attachment:
- With assistance, position the Bull Bar onto the outside of both installed Mounting Brackets.
- Attach the Bull Bar to the brackets using the provided hardware:
  - (4) 8mm x 30mm Hex Bolts
  - (8) 8mm Flat Washers
  - (4) 8mm Nylon Lock Nuts
Adjustment and Tightening:
- Level and adjust the Bull Bar to the desired position.
- Tighten all hardware securely at this stage.

Maintenance Features:

Periodic Inspections: Regular inspections of the installation are recommended to ensure all hardware remains secure and tight.
Protective Waxing:
- After installation, it is recommended to wax the product.
- Regular waxing adds a protective layer to the finish.
- Caution: Do not use polishes or waxes that contain abrasives, as these can damage the finish.
Cleaning (Stainless Steel):
- Small scratches and scuffs on stainless steel finishes can be polished using aluminum polish.
- Mild soap can also be used for general cleaning.
Cleaning (Gloss Black Finishes):
- Only mild soap should be used to clean gloss black finishes.

Steelcraft 70280B Specifications

General

Brand	Steelcraft
Model	70280B
Category	Automobile Accessories
Language	English

Related product manuals