Stewart Filmscreen Corp C

Questions and Answers

K
Kevin EstesAug 15, 2025
How to troubleshoot a Stewart Filmscreen Corp C that won't operate?
- A
  amberhallAug 15, 2025
  If your Stewart Filmscreen Corp Projection Screen isn't operating, the issue might be due to a lack of power. Check if the circuit breaker has been switched off and reset it if necessary. Also, verify the voltage availability. If needed, contact an electrician.
K
Kyle JohnsonAug 18, 2025
How to clean dirt and fingerprints off my Stewart Filmscreen Corp C Projection Screen?
- K
  Kaitlyn AlvaradoAug 18, 2025
  If you have dirt, fingerprints or marks on the surface of your Stewart Filmscreen Corp Projection Screen, it is likely due to improper handling. Try brushing them off or using a mild detergent solution with a clean rag or cotton swab.
M
Melody PerezAug 21, 2025
What to do if my Stewart Filmscreen Corp C won't roll up or down with power?
- J
  Jessica GrahamAug 22, 2025
  If your Stewart Filmscreen Corp Projection Screen isn't rolling up or down even though power is available, there may be a bad connection at the switch. Have an electrician or qualified service person check the connection as follows: * If you have a high voltage control switch, check switch-line connections. * If you have a low voltage control unit, check switch-line connections. * If you have a screen trigger interface, check line connections, or the mini-plugs at the screen input or projector output. Contacts may be sticking—tap relay to free contacts.
J
Jorge WrightAug 26, 2025
Why does my Stewart Filmscreen Corp C Projection Screen drop when activated with a grinding noise?
- N
  nrhodesAug 26, 2025
  If your Stewart Filmscreen Corp Projection Screen drops when the up direction is activated and makes a grinding noise, it could be due to a drop in voltage. The screen motor requires full voltage. Have an electrician or qualified service person check the available voltage.
J
Joy MontgomeryAug 28, 2025
What causes a Stewart Filmscreen Corp C to continue past the bottom stop position?
- M
  michellehaynesAug 28, 2025
  If your Stewart Filmscreen Corp Projection Screen continues past the bottom stop position, the white limit switch is likely out of adjustment. Readjust the white DOWN limit switch by turning the adjusting screw clockwise.
T
Timothy RodriguezAug 31, 2025
Why does my Stewart Filmscreen Corp C roller chatter when power is activated?
- K
  Kathleen CamachoSep 1, 2025
  If your Stewart Filmscreen Corp Projection Screen roller chatters when power is activated, it can be caused by voltage drop, bad connections, or a defective switch. Have an electrician or qualified service person check all hook-ups including all outboard wiring.
S
santiagojoshuaSep 4, 2025
Why does my Stewart Filmscreen Corp Projection Screen hum in up mode after retracting?
- R
  Ryan HamiltonSep 4, 2025
  If your Stewart Filmscreen Corp Projection Screen hums in up mode after the screen has already retracted, the screen batten may be retracting too far into the case. This can damage the motor and screen if not corrected. Have a qualified service person adjust the yellow UP limit switch by turning the adjusting screw clockwise.
N
Nicholas NunezSep 7, 2025
What to do if the batten retracts too far into the case of my Stewart Filmscreen Corp C?
- S
  stephanieburchSep 7, 2025
  If the batten of your Stewart Filmscreen Corp Projection Screen retracts too far into the case, the yellow limit switch may be out of adjustment, which can damage the motor and screen if not corrected. Have a qualified service person readjust the yellow UP limit switch by turning the adjusting screw clockwise.
J
Joseph SantosSep 12, 2025
Why are there indentations on my Stewart Filmscreen Corp C Projection Screen surface?
- S
  Sierra LiSep 12, 2025
  If indentations appear on your Stewart Filmscreen Corp Projection Screen surface, it is because of debris or particles adhering to the screen due to static cling. Check the back of the screen and gently brush debris away by hand.