How to clean dirt, fingerprints or marks on Stewart Filmscreen Luxus?
If you notice dirt, fingerprints, or marks on your Stewart Filmscreen projection screen, it's likely due to improper handling. To resolve this, lightly brush off the screen or use a mild, water-based detergent solution applied with a clean rag or cotton swab.
What to do if Stewart Filmscreen Projection Screen motor shuts off?
If the motor of your Stewart Filmscreen projection screen shuts off, especially after more than 2 minutes of use, it's because the motor is designed for short operations and overheats with continuous use. To fix this, allow the motor to cool down completely, which can take an hour or more. Remember that heat gain is cumulative, so ensure it's fully cooled before resuming use to prevent another shutdown.
What to do if Stewart Filmscreen Projection Screen batten retracts too far into case?
If the batten of your Stewart Filmscreen projection screen retracts too far into the case, it indicates that the “yellow” limit switch is out of adjustment. It is recommended to have a qualified service person adjust the “yellow up” limit switch. Continued use without correction can damage the motor and screen, so do not use the unit until this is resolved.
Why Stewart Filmscreen Luxus Projection Screen roller chatters when power is activated?
If your Stewart Filmscreen projection screen roller chatters when power is activated, it could be due to voltage drop, bad connections, or a defective switch. To address this, have an electrician or qualified service person check all hookups, including outboard wiring.
What to do if Stewart Filmscreen Luxus Projection Screen drops when “up” direction is activated?
If your Stewart Filmscreen projection screen drops when the “up” direction is activated, it could be due to a drop in voltage. The screen motor requires full voltage to operate correctly. Have an electrician or qualified service person check the available voltage.
What to do if Stewart Filmscreen Luxus won't roll up or down?
If your Stewart Filmscreen projection screen won't roll up or down, even with available power, it could be due to a bad connection at the switch or incorrect polarity of the IMC line. Have an electrician or qualified service person check the control board connections.
What to do if Stewart Filmscreen Luxus Projection Screen continues past bottom stop position?
If your Stewart Filmscreen projection screen continues past the bottom stop position, the “white” limit switch is likely out of adjustment. Readjust the “white” down limit switch. Refer to the section on Adjusting Screen Deployment of this manual (Page 24).
Why Stewart Filmscreen Luxus Projection Screen hums in “up” mode?
If your Stewart Filmscreen projection screen hums in “up” mode, it means the screen batten is retracting too far into the case. It is recommended to have a qualified service person adjust the yellow UP limit switch. Failure to correct this can damage the motor and the screen. Do not use the unit until this problem is resolved.
How to remove indentions that appear on Stewart Filmscreen Projection Screen surface?
If indentions appear on your Stewart Filmscreen projection screen's surface, it is caused by debris or particles adhering to the screen due to static cling. Check the back of the screen and gently brush the debris away with a soft brush.
What to do if Stewart Filmscreen Projection Screen won't operate?
If your Stewart Filmscreen projection screen isn't operating, the cause may be a lack of AC power. First, check if the circuit breaker has tripped and reset it if necessary. Also, inspect the outboard switching apparatus and verify voltage availability. If problems persist, contact an electrician.
Crucial safety guidelines for installation and use of the screen system.
Guidance on navigating the manual for specific installation procedures and controls.
Pre-installation checks, planning for people, and required tools.
Lists the contents included in the Luxus unit box for setup.
Lists the tools and materials required for installation.
Instructions on careful unpacking and retaining packing material for future use.
Details about the two 18-inch mounts included for wall or ceiling installation.
Specifies the type and quantity of fasteners required for secure mounting.
States that the motor is prewired at the factory, requiring no additional wiring.
Lists Stewart Filmscreen accessories that connect via RJ45/RJ25 ports.
Introduces the process of connecting the IR eye to the Luxus unit.
Explains how to operate the screen using the IR remote for extending, retracting, and stopping.
Introduces the process of connecting the 3.5mm trigger cable to the projector and unit.
Explains how the 12V trigger signal from the projector controls screen movement.
Step-by-step guide for programming the RTS motor limits and settings.
Instructions on how to adjust the lower and upper limits of the screen in User Mode.
Steps for adding or deleting transmitters and channels for the RTS motor.
Instructions for connecting the IR wall switch to the Luxus unit.
Explains how to operate the screen using the IR wall switch and remote.
Instructions for connecting the Decora paddle wall switch to the unit.
Steps to connect the IBT-100 for serial RS-232C connectivity.
Guides on adjusting the lower limit switch for the screen's deployed position.
Guides on adjusting the upper limit switch for the screen's retracted position.
General advice on keeping the screen clean and handling it with care.
General| Brand | Stewart Filmscreen |
|---|---|
| Model | Luxus |
| Category | Projection Screen |
| Language | English |
To Next Page