To Next PageTo Next Page
Need help?Do you have a question about the STI E2410FN000/010 and is the answer not in the manual?
Read manual carefully, handle product with care, and do not use it differently from instructions.
Visual representation of the STI Front Under Spoiler correctly installed on the front bumper.
Verify all listed parts and quantities are present before starting the installation process.
List of tools and materials needed for installation, including degreasing agent, clips, and fasteners.
Prepare the vehicle by parking on a level surface, applying the brake, and cleaning the bumper.
Remove existing vehicle clips from the bottom and wheel arch surface of the front bumper.
Position template A on the grille, mark holes, and drill pilot (3mm) and final (6mm) holes.
Use cloth adhesive tape as a stopper and remove burrs after drilling to prevent damage.
Position template B on the lower bumper surface, mark, and drill pilot (3mm) and final (6mm) holes.
Position templates C, D, E, mark holes, and drill pilot (3mm, 6mm) and final (9.5mm) holes.
Apply tape stopper to drills to avoid interfering with or damaging other parts.
Insert the supplied Wellnuts into the 9.5 mm holes carefully, avoiding over-tightening.
Clean and degrease the shaded area of the rear bumper with a degreasing agent and dry thoroughly.
Peel half the release paper from double-sided tape, fold over, and attach to the bumper surface.
Attach using Medium Clips (3) on the wheel arch and Small Clips (4) in the center 6mm holes.
Use a Phillips screwdriver to temporarily tighten the remaining bottom fastening holes with Bolts (7).
Press the adhesive part firmly, pulling release paper slowly to avoid breaking it in the middle.
Fully tighten the Bolts (7) on the bottom surface of the spoiler with a Phillips screwdriver.
Check float, inclination, ensure no missing clips/bolts, and confirm all tightening is complete.
Be cautious of curbs, steps, and snow as product may scratch, deform, or detach if impacted.
Template for drilling 6.0mm holes on the front bumper, ensure scale is 1/1 when printing.
Templates for drilling 9.5mm holes, use after copying to ensure correct 1/1 scale.
Templates for drilling 9.5mm holes, ensure scale is 1/1 when printing for accuracy.
Templates for drilling 9.5mm (E) and 6.0mm (B) holes, cut on the outside of the line.
Read manual carefully, handle product with care, and do not use it differently from instructions.
Visual representation of the STI Front Under Spoiler correctly installed on the front bumper.
Verify all listed parts and quantities are present before starting the installation process.
List of tools and materials needed for installation, including degreasing agent, clips, and fasteners.
Prepare the vehicle by parking on a level surface, applying the brake, and cleaning the bumper.
Remove existing vehicle clips from the bottom and wheel arch surface of the front bumper.
Position template A on the grille, mark holes, and drill pilot (3mm) and final (6mm) holes.
Use cloth adhesive tape as a stopper and remove burrs after drilling to prevent damage.
Position template B on the lower bumper surface, mark, and drill pilot (3mm) and final (6mm) holes.
Position templates C, D, E, mark holes, and drill pilot (3mm, 6mm) and final (9.5mm) holes.
Apply tape stopper to drills to avoid interfering with or damaging other parts.
Insert the supplied Wellnuts into the 9.5 mm holes carefully, avoiding over-tightening.
Clean and degrease the shaded area of the rear bumper with a degreasing agent and dry thoroughly.
Peel half the release paper from double-sided tape, fold over, and attach to the bumper surface.
Attach using Medium Clips (3) on the wheel arch and Small Clips (4) in the center 6mm holes.
Use a Phillips screwdriver to temporarily tighten the remaining bottom fastening holes with Bolts (7).
Press the adhesive part firmly, pulling release paper slowly to avoid breaking it in the middle.
Fully tighten the Bolts (7) on the bottom surface of the spoiler with a Phillips screwdriver.
Check float, inclination, ensure no missing clips/bolts, and confirm all tightening is complete.
Be cautious of curbs, steps, and snow as product may scratch, deform, or detach if impacted.
Template for drilling 6.0mm holes on the front bumper, ensure scale is 1/1 when printing.
Templates for drilling 9.5mm holes, use after copying to ensure correct 1/1 scale.
Templates for drilling 9.5mm holes, ensure scale is 1/1 when printing for accuracy.
Templates for drilling 9.5mm (E) and 6.0mm (B) holes, cut on the outside of the line.
General| Brand | STI |
|---|---|
| Model | E2410FN000/010 |
| Category | Automobile Accessories |
| Language | English |
