Characteristics
Communication: RS485 (L+ & L-) / TTL (Wiegand / Clock and Data)
Connector output: - 8 female stamped crimp terminals 28-22AWG (Wurth Electronik 62400113722DEC)
- 8 points female dual-row terminal housing (Wurth Electronik 624008213322)
(use Crimp Hand Tool
WURTH ELEKTRONIK
600624228220)
Cable output: TRANXALARM - 8x0,22mm
2
– Length 3.05m
Protection: IP65 classified reader
Buzzer / LED
The operating mode for the Buzzer and LED 1 and 2 can be programmed by a configuration card (SCB / OCB) or controlled by the remote system with a 0 Vdc
respectively on the “
Led 1
”, “
Led 2
” and “
Buzzer
” inputs of the reader’s connector or controlled by the communication protocol of the reader (SSCP
®
/ OSDP
TM
).
Anti-tearing
Tearing is detected by an accelerometer. When the reader is wrenched:
• for R/S 31: the wrenching signal will be emitted on the “Data/Data1” line. This function is configurable via a configuration card.
▪ for R/S 33 and OSDP
TM
: the reader will perform the operations configured with the configuration card.
▪ for W33: the reader will perform the operations configured with the SSCP
®
protocol.
Caution: switch on the reader when it is in its final position to initialize the accelerometer in the correct position.
Read-only reader configuration
R and S readers are configurable with SCB RFID / Virtual configuration card.
OSDP
TM
readers are configurable with OCB RFID / Virtual configuration card or with FileTransfer command.
▪ If the SCB/OCB is compatible with the reader’s firmware, the LED lights green and the buzzer beeps five times.
▪ If the SCB/OCB is not compatible with the reader’s firmware, the LED lights red and the buzzer is activated for 1 s.
▪ If the SCB/OCB key is different from the reader’s key: no reaction.
Caution: set your reader with your own company key.
Powering-up the readers
On power-up, the reader enters an initialization phase:
1. Activation of the white LED and buzzer for 100 ms.
For read-only readers and OSDP
TM
readers:
2. Activation of the LED, according to the color code: Red = +10, Orange = +5, Green = +1, indicating the firmware version.
3. For serial R/S reader only: the orange LED flashes 20 times: waiting for an update.
4. For Bluetooth
®
reader only: Activating white fixed LED during Bluetooth initialization.
5. Activation of the default LED (read-only: flashes blue, OSDP
TM
: off; if no customer specific configuration).
Caution for Bluetooth reader
Caution: at the reader Bluetooth (BT1) powering, make sure that nothing is in an area of at least 10 cm / 3.94 in. around the reader (ex. No hand in front
of the reader…).
TBLOCK option
Connection
- Press the orange part to open.
- Insert the wire.
- Release the orange part.
- Check that the wire is correctly clipped.
Precautions for installation
▪ The supply voltage at the reader’s connector should be between +9 Vdc and +15 Vdc.
▪ As far as possible, keep the reader away from computer or power source cables. They can generate electrical interference, depending on their radiation level and
the proximity of the reader.
▪ Recommended distance between two readers: parallel plane: 15.8 in – same plane: 15.8 in – perpendicular plane: 11.8 in.
▪ Recommended distance between two Bluetooth
®
readers: 2 meters / 78.74 inch either plan.
▪ Place the reader at a height of less than 2 meters / 78.74 inch (standard UL/IEC 62368).
▪ If the reader is fixed on a metal surface, it is possible to have a reduction in the reading distance.
▪ Use a ferrite (two-way) for the cable (power supply and data).
Example: reference 74271222 WURTH ELEKTRONIK
.
▪ By design, the reader can be installed indoors and outdoors.
▪ BEFORE powering on, connect the wires or the connector of the reader. Before disconnecting the wires or the connector of the reader, power off.
▪ Operating temperature: -4 °F to 158 °F / -20°C à +70°C.
To Next Page
Need help?
General