STIEBEL ELTRON DHE 18 AU - Page 7

OPERATION
Settings and displays
ENGLISH
www.stiebel-eltron.com DHE AU| 7
1 ECO water and energy saving function
The ECO function enables you to limit the flow rate to a maxi-
mum value.
ECO on = symbol on user interface
ECO off = no symbol on user interface
2 Childproofing
Childproofing allows you as a user to limit the adjustable temper-
ature at the appliance to a maximum value. In service mode, your
qualified contractor can also set a temperature for anti-scalding
protection (see chapter "Service mode"). This temperature then
acts as the upper limit of the setting range for childproofing.
3 Wellness shower programs
The Wellness shower program lets you choose from 4 different
alternating shower programs.
WW = domestic hot water, KW = cold water
A Cold prevention
To strengthen the body, we recommend you finish off with a
cold shower; this will trigger a reflex in the body to warm up.
3 min
WW
KW
B Winter pick-me-up
An invigorating end to a winter shower with a final warm-up.
– 10°C
WW
WW
3 min
10 sec
10 sec
10 sec
10 sec
C Summer fitness program
The quick contrast shower to increase fitness with a final
warm-up.
WW
KW
3 min
10 sec
10 sec
10 sec
10 sec
D Circulation program
Shower your arms and legs with cold water to boost circu-
lation. Spray from the hands and feet towards the body. You
can then repeat this process with hot water.
WW
KW
3 min
20 sec
20 sec
30 sec
30 sec
4 Automatic water volume control
The automatic water volume control allows you to limit the volume
of water at a high flow rate. When the selected volume of water
is reached, the control automatically reduces the flow rate. The
required temperature is maintained. The automatic water volume
control must be enabled on each occasion prior to filling the bath.
Example of filling a bath with 80 litres: When the bath has been
filled with 80 litres, the control automatically reduces the flow
rate to 4 l/min.
5 Flow rate
You have the option of displaying the flow rate or the time.
6 Setting the time
You have the option of displaying the time or the flow rate. You
can set a time from 00:00 h to 23:59 h. You will need to set the
time again following a power interruption.
7 Adjusting the backlighting
You are able to adjust the display backlighting. If you select "Auto"
the illumination will flash during the setting process.
- The backlighting switches on whenever the appliance heats
and with any operation of the user interface.
- If there is no operation for 30seconds the backlighting
switches off.
- If you select "On" the backlighting will remain on constantly.
8 Adjusting the green/amber brightness
You can adjust the brightness of both backlighting colours indi-
vidually.
9 Selecting the currency
Here you can select the currency you wish to display for the en-
ergy and water saving:
Eur = €
cur = any other currency
10 Setting the electricity tariff
Here you can enter your particular electricity tariff in Eur/kWh or
cur/kWh in order to calculate the energy saving.
11 Setting the water tariff
Here you can enter your particular water tariff in €/m³ or cur/m³
in order to calculate the water saving.
12 Setting the CO2 emissions value
The factory default for the CO2 emissions calculation is 553 g
CO2⁄kWh (source: "Reducing energy consumption and CO2 emis-
sions through electrical domestic hot water supply", 2011). You can
also set your own CO2 emissions value if required.
13 Resetting to factory defaults
 Press keys M and i simultaneously for 2 seconds.
The default settings can be found in the dashed box in the dia-
gram.
14 Menu item
This parameter is not relevant to this version of the appliance. It
is not possible to adjust any settings.
15 Menu item
This parameter is not relevant to this version of the appliance. It
is not possible to adjust any settings.