Installing the machine
Model Number STR-FLW10W
Let’s get your new 10kg front load
washing machine ready to use!
Quick Start Guide
Preparing a wash
3
8
4
5
10
6
B
C
Before washing a load, plug in the machine and open
your water tap.
Load your washing into the machine—page 24 in the
instruction manual has useful hints to help you with this.
Close the door and add detergent to the drawer—find all
the details on page 23 in the instruction manual.
CAUTION! This washing machine is extremely heavy—transport it with care! A team lift or mechanical aid is
required when moving it.
IMPORTANT! Before installing the washing machine, you must remove the transport bolts from the back of
the housing and cover the holes with the transport hole caps provided. The four bolts hold the drum in place
during transport but they must be removed before use so the drum can move during the wash and spin cycles.
This washing machine must be installed by a competent person. Installation involves removing the transport
bolts, levelling the machine, connecting it to your cold water supply and installing the drain hose. For detailed
installation instructions, please consult the supplied instruction manual, which also has comprehensive
usage instructions and important safety advice.
NOTE: Make sure the washing machine is properly and securely installed. Before using the washing machine
for washing clothes, run a complete washing cycle without clothes using the drum clean program.
A
Control panel operation
Turn over the page for details about the
wash programs ...
Rotate the program dial to switch on the machine,
select a program and switch the machine off at the end.
The display screen shows the settings,
time remaining, options, codes, etc.
Use the buttons to set a delay start time
or an extra rinse, or adjust the spin speed
and water temperature.
Press the Start/Pause button to start a
wash program or to pause it.
Press and hold a button, as instructed on
the panel, to activate the Wi-Fi module or
child lock, or to mute the alert sound.
7
9
11
3
5
6
4
1
2
SY-XT5QG100-006
材料:油墨
中山格兰仕日用电器有限公司
设 计
校 对
审 核
工 艺
标准化
批 准
日 期
李东波
宾艺强
洪柳
傅玲
尹怀斌
2021.07.10
控制面板丝印
XQG100-T514VE/W
标记 更改文件号处数 签名 日期 阶 段标 记
B
重量 比例
视 角
共1页 第1页
叶强
技术要 求：
1.文字 字体格 式、大 小尺寸 必须与 图纸相 符合；
2.文字 、图案 排版必 须与图 纸一致;
3.未注 公差按 照IT1 4执行。
SY-XT5QG100-006 00
版本
大于
—
6
3
10
18
30
基本尺寸
公差 值±
IT12
IT13 IT14 IT15 IT16 IT17 IT18
到
80
50
12 0
18 0
25 0
31 5
40 0
50 0
3
10
6
18
30
50
12 0
80
18 0
25 0
31 5
40 0
50 0
—
mm
0.1
0.14
0.25
0.4
0.6
1.0 1.4
0.12
0.18
0.3
0.48
0.75
1.2 1.8
0.15
0.22
0.36
0.58
0.9
1.5 2.2
0.18
0.27
0.43
0.7
1.1
1.8 2.7
0.21
0.33
0.52
0.84
1.3
2.1 3.3
0.25
0.39
0.62
1.0
1.6
2.5 3.9
0.3
0.46
0.74
1.2
1.9
3.0 4.6
0.35
0.54
0.87
1.4
2.2
3.5 5.4
0.4
0.63
1.0
1.6
2.5
4.0 6.3
0.46
0.72
1.15
1.85
2.9
4.6 7.2
0.52
0.81
1.3
2.1
3.2
5.2 8.1
0.57
0.89
1.4
2.3
3.6
5.7 8.9
0.63
0.97
1.55
2.5
4.0
6.3 9.7
0.7
1.1
1.75
2.8
4.4
7.0 11.0
公差 值±
角度
IT12/13/14IT15/16/17/18
大于 到
0°
90°
5′
90′
90°
18 0°
15′
1°
18 0°
27 0°
30′
2°
27 0°
36 0°
1°
6°
技术要求：
1.文字字体格式、大小尺寸必须与图纸相符合；
2.文字、图案排版必须与图纸一致;
3.未注公差按照IT14执行；
4.丝印图文清晰、正确光洁、颜色均匀；
5.丝印线条宽度一致，不允许有缺印、漏印；
6.丝印附着力:采用正己烷、1kg砝码，水拉动
15秒，测试完成后丝印油墨无脱落。
7
8
9 10
11
To Next Page
Need help?
General
