Stoneridge SE5000 Exakt Duo

To Next Page

SE5000 Rev.7.4, 102024P/01R03 EN

Note! Card handling and browse in menu is only possible when vehicle is not moving.

STONERIDGE - SETTING THE STANDARD

For full details on the SE5000 funconality we refer to the

Driver & Company Manual or visit www.SE5000.com

Company Quickguide

SE5000 Digital Tachograph

Insert the card (always possible in standard menu and ignion ON)

1. Press and hold the driver or co-driver buon unl tray opens.

2. Insert the card with the chip facing upward.

3. Close the tray by pushing it gently forward.

Withdraw the card (not possible in all menus)

1. Press and hold the driver or co-driver buon unl tray opens.

2. Press the card up slightly from underneath through the opening in the tray

or push the edge of the tray down unl the card pops out.

Driver

buon

Co-driver

card tray

Paper

cassee

Driver

card tray

Co-driver

buon

Cancel, move back to previous display

Select, highlight, change values

Conrm, move forward in displays

Default Acvity key on/o

This seng gives the opportunity to preset an automac acvity change for

both driver and co-driver when switching the ignion key on or o (consult

relevant authority for naonal regulaons).

1. Press the conrm buon.

Select and conrm Sengs.

2. Select and conrm Parameters.

3. Select and conrm Default acv.key on or

Default acv.key o.

4. Select and conrm the preferred acvity; No

change, Rest, Available or Work.

5. The following is displayed.

6. Press the cancel buon three mes to re-

turn to the standard display.

Daylight Saving Time

An automac local me adjustment for summer and winter is automacally

prompted on the last Sunday in March and last Sunday in October, respecvely.

1. Select YES to acknowledge or NO to cancel

the me change.

03:01

Default activ.

key on

Default activ.

key off

Changes

saved

New time?

Parameters

SETTINGS

YES

Ready to

drive

Need help?

Do you have a question about the Stoneridge SE5000 Exakt Duo and is the answer not in the manual?

Summary

Default Activity Key On;Off Configuration

Accessing and Setting Default Activity

Configure the default activity key for ignition on/off and select preferred activity (No change, Rest, Available, Work).

Card Handling and Menu Navigation

Instructions on inserting and withdrawing driver/co-driver cards and navigating the tachograph menu.

Daylight Saving Time Adjustment

Automatic Time Change Prompt

Respond to the automatic local time adjustment prompt for summer/winter time.

Company Lock-in and Lock-out

Performing Company Lock-in

Secure tachograph data by locking into the company mode before use.

Performing Company Lock-out

Unlock the tachograph before transferring to a new company/owner to prevent data security risks.

Vehicle Unit Download

Preparing for Download

Remove printer cassette and attach download equipment to the tachograph.

Initiating and Completing Download

Download data while ignition is ON and check status messages for success or failure.

The SE5000 Digital Tachograph is a device designed to record and store vehicle and driver activity data. It features a user-friendly interface with a display and buttons for various operations. The device supports both driver and co-driver cards, as well as paper cassettes for printing.

Function Description

The primary function of the SE5000 is to automatically record driving, working, availability, and rest times for drivers and co-drivers. This data is crucial for compliance with regulations and for managing driver activities. The device also supports company lock-in and lock-out features to secure data and prevent unauthorized access. Additionally, it allows for the download of vehicle unit data for further analysis and record-keeping.

Usage Features

Default Activity Key On/Off:

The device offers an automatic activity change feature. When a driver or co-driver card is inserted, the ignition is turned on or off, or the vehicle is moved, the tachograph can automatically set the activity. This feature can be enabled or disabled through the settings menu. To adjust this:

Press the confirm button.
Select and confirm "Settings."
Select and confirm "Parameters."
Select and confirm "Default activ. key on" or "Default activ. key off."
Select and confirm the preferred activity: "No change," "Rest," "Available," or "Work."
The following message will be displayed: "Changes saved."
Press the cancel button three times to return to the standard display.

Daylight Saving Time:

The device can automatically adjust for summer and winter time changes. This feature is typically programmed to occur on the last Sunday in March and last Sunday in October, respectively. To acknowledge or cancel the time change:

Select "YES" to acknowledge or "NO" to cancel the time change.

Card Operations:

The SE5000 uses driver cards, co-driver cards, and company cards.

Inserting a Card: To insert a card, hold the card with the chip facing upward and push the card gently forward into the appropriate tray.
Removing a Card: To remove a card, press and hold the driver or co-driver button until the tray opens. Then, pull the card out.

Company Lock-in:

To prevent unauthorized access to tachograph data, a lock-in procedure should be performed before using the tachograph.

Insert a company card into either tachograph tray. The tachograph will automatically enter company mode.
Press the confirm button to enter the tachograph menu.
Select and confirm "COMP LOCKS."
Confirm with "YES" to perform the lock-in.
After confirmation, the message "Lock-in complete" will be displayed.

Company Lock-out:

A lock-out (unlock) must be performed before transferring the tachograph to another company or owner. This ensures that data is not recorded under the current company for subsequent users. It is crucial to download data before performing a lock-out.

Insert a company card into either tachograph tray. The tachograph will automatically enter company mode.
Press the confirm button to enter the tachograph menu.
Select and confirm "COMP LOCKS."
Confirm with "YES" to perform the lock-out.
After confirmation, the message "Lock-out complete" will be displayed.

Vehicle Unit Download:

The device allows for downloading data from the vehicle unit.

Remove the printer cassette.
Attach the download equipment to the tachograph through the 6-pin download connector.
Download the data according to the instructions on the downloading equipment. Ensure that the ignition is ON when starting the download.
During the download, the message "Downloading busy" will be displayed.
Upon completion, the message "Download complete" will be displayed.
If the download fails, the message "Download failed" will be displayed. In such cases, check the connections and downloading equipment. Refer to the Driver & Company Manual (Company Mode) for further information.

Maintenance Features

Printer Cassette:

The device uses a paper cassette for printing data.

Withdraw the Cassette: To withdraw the cassette, press and hold the driver or co-driver button until the tray opens. Then, press the card up slightly from underneath through the opening in the tray or push the edge of the tray down until the card pops out.
Removing the Printer Cassette: The manual indicates that the printer cassette needs to be removed for certain operations, such as vehicle unit download. The process involves opening the cassette compartment and pulling out the cassette.
Replacing the Printer Cassette: To replace the cassette, insert it into the compartment until it clicks into place.

The SE5000 Digital Tachograph is designed for ease of use and compliance, providing essential features for managing driver and vehicle data effectively.