STRIKEMASTER LITE-FLITE LAZER User Manual

HOW TO ATTACH THE SIDE HANDLE AND USE THE CORRECT GRIP.
HOW TO OPERATE THE CORDLESS DRIVER WITH THE LITE-FLITE LAZER
™
DRILL UNIT
HOW TO ATTACH THE NDA-3 DRILL ADAPTER TO THE CORDLESS DRIVER
SAFE USE OF CORDLESS DRIVER AND LITE-FLITE LAZER
™
DRILL UNIT
Attach the side handle to the drill unit. Always securely hold the side-handle when drilling ice.
Place the NDA-3 adapter into
the center of the FND flange.
Open the chuck with your hands.
DO NOT use trigger to rotate the chuck.
Tighten the chuck on to the adapter
by hand. DO NOT use the trigger to
tighten the chuck.
DO NOT use the trigger or wear gloves
while tightening the chuck, may cause
serious injury.
Push the adapter into the open chuck.
Line up the chuck teeth with the flat
sides of the adapter.
Use the lowest speed setting on the
cordless driver.
DO NOT drill with only one hand.
DO NOT hold the ice drill unit, flange or drill chuck while drilling ice.
Always place your thumb on top of the
side-handle.
DO NOT lock your grip with your
thumb around the side-handle.
DO NOT drill ice without holding
the side-handle on the cordless driver.
DO NOT use the cordless driver’s
hammer or impact function.
Push the flange with adapter into the collar of the drill unit.
Connect flange and adapter to drill unit, using collar bolt
and hex wrench.
Always place your thumb
on top of the side-handle.
DO NOT lock your grip with your
thumb around the handle.
Push the adapter in firmly
until it locks into the flange.
Insert bolt into the top hole
on the non-threaded side of
the collar.
ASSEMBLY AND SAFE USE INSTRUCTIONS
STRIKEMASTER
®
LITE-FLITE LAZER
™
DRILL UNIT,
THE NDA-3 DRILL ADAPTER & FND SAFETY FLANGE
©2021 StrikeMaster, Inc. 0822
Suite 100, 935 Aldrin Drive, Eagan, MN 55121
USA customer service email:
strikemaster@rapalausa.com
TOLL-FREE HELPLINE: 1-877-572-7278
(Monday - Friday / 8am - 4:30pm CST)
www.strikemaster.com
1350 Phillip Murray Ave,
Oshawa, ON L1J 6Z9, Canada
cacustserv@rapalavmc.com
TOLL-FREE HELPLINE: 905-571-3001
(Monday - Friday / 8am - 4:30pm ET)
www.strikemaster.ca
Always keep hands, feet, hair and loose clothing
away from the rotating auger. Failure to do so
may cause serious injury.
Check blade screws before each use.
Cutting blades are sharp, keep away from body.
WARNING
CAUTION

STRIKEMASTER LITE-FLITE LAZER Specifications

General

Brand	STRIKEMASTER
Model	LITE-FLITE LAZER
Category	Tools
Language	English

Summary

Assembly and Safe Use Instructions

Attaching the NDA-3 Adapter to the FND Flange

Steps for placing and locking the NDA-3 adapter into the FND flange.

Connecting Flange and Adapter to Drill Unit

Procedure for connecting the flange and adapter to the drill unit using a collar bolt and hex wrench.

Inserting the Collar Bolt

Instructions for inserting the bolt into the top hole on the non-threaded side of the collar.

Safe Use of Cordless Driver and Lite-Flite Lazer Drill Unit

Attaching Side Handle and Correct Grip

Guidance on attaching the side handle and maintaining a proper grip while drilling ice.

Attaching Adapter to Cordless Driver

Steps for opening the chuck, inserting the adapter, and tightening the chuck securely.

Operating the Drill Unit Safely

Key operational guidelines including speed settings, avoiding hammer function, and proper handling.

Important Safety Warnings and Cautions

General Safety Warning

Warning to keep body parts and clothing away from the rotating auger to prevent injury.

Blade Caution

Caution to check blade screws before use and keep away from body due to sharpness.