EasyManua.ls Logo

Stromag KMB 12 ZM - User Manual

Default Icon
96 pages
Go to English
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Druckmittelgeschaltete
Lamellen-Federdruckbremse
KMB-ZM, KLB-ZM
Dokumenten-Nr.: 777-00001 D
Datum: 10.2017
SKB-0398
Montageanleitung
DE
Stromag GmbH
Hansastraße 120
D-59425 Unna
Tel.: +49 (0) 2303 102-0
Fax: +49 (0) 2303 102-201
www.stromag.com
info@stromag.com

Table of Contents

Questions and Answers

  • E
    Emily VargasAug 7, 2025
    What to do if the braking action is insufficient in Stromag KMB 12 ZM Industrial Equipment?
    • H
      hansonchristineAug 7, 2025
      If the braking action of your Stromag Industrial Equipment is insufficient, it could be due to several reasons. One potential cause is that the inner disc was not degreased when it was replaced. In this case, degrease the friction surface. Another reason might be that the permissible wear has been exceeded, so replace the disc pack. Finally, there might be residual pressure present in the pressure line, so check the cause and find a corrective action.
  • K
    Kayla WebbAug 22, 2025
    Why is the Stromag Industrial Equipment brake too warm?
    • M
      Michael HarveyAug 22, 2025
      If your Stromag Industrial Equipment brake is too warm, it could be due to the minimum excessive release pressure for opening the brake not being present. Check this using the dimensional drawing. Alternatively, if the lubricant is too thick, causing idling heat, you should contact Stromag's Customer Care.

Summary

For your safety

2.1 Safety concept of the documentation

2.2 Required personnel qualifications

Specifies the necessary qualifications for personnel performing various tasks related to the brake.

2.3 Intended use

2.4 Non-intended use

Details uses that are not permitted and may lead to dangerous situations.

2.6 Possible residual risks

Identifies inherent dangers that cannot be eliminated despite safety-oriented construction.

2.7 Safety symbols;pictograms in the documentation

2.7.2 Hazard classifications

Defines hazard levels (DANGER, CAUTION, ATTENTION) and their implications.

2.7.3 Mandatory symbols

Illustrates and explains mandatory symbols for personal protective equipment.

2.8 Safety devices on the brake

Specifies responsibilities for enclosing the brake with safety guards.

2.10 Wear personal protective equipment

Emphasizes the importance of wearing personal protective equipment for all work.

2.11 Basic responsibilities of the operator and personnel

Outlines fundamental duties of operators and personnel for safe handling of the brake.

Technical specifications

4.2 Operating conditions

4.3 Dimensional drawing

Assembly

6.1 Special safety guidelines

Highlights safety precautions to be observed during the assembly process.

6.2 Pre-mounting condition

6.3 Conditions for assembly and fixing

6.4 Assembling the brake

Provides step-by-step instructions for the actual assembly of the brake unit.

Operation

7.1 Special safety guidelines

Emphasizes safety instructions specifically related to operating the brake.

7.2 Initial commissioning

7.5 Recommissioning

Maintenance and inspections

8.1 Special safety guidelines

Stresses safety precautions essential for performing maintenance and inspection tasks.

8.4 Maintenance and inspection intervals

Troubleshooting

9.1 Operational issues and their solutions

Lists common operational faults, their possible causes, and recommended corrective actions.

Disassembly

10.1 Special safety guidelines

Emphasizes safety precautions crucial for safe disassembly procedures.

10.2 Disassemble the brake (completely)

10.3 Dismantle the brake

10.4 Final decommissioning

Ordering spare parts

11.1 Data for ordering spare parts

11.2 Service address

Stromag KMB 12 ZM Specifications

General IconGeneral
TypeKMB 12 ZM
Electromagnetic brakeYes
Nominal torque12 Nm
Voltage24 VDC
Housing materialAluminum
Protection classIP54
Weight1.5 kg

Related product manuals