Strong 210 - User Manual

Component Overview
USER MANUAL
English
NAIL
DRILL
210
Specifications
Control Box Handpiece
Input Voltage
Size
(LxWxH)
Weight
Model Length
Rotation
Speed
Torque
Weight
110/220 V
50/60 Hz
11
6
12
14
3
8
7
1
109
54
13
1 - Speed control knob
2 - Control box
3 - Forward/Reverse (FWD/REV) switch
4 - Voltage selector switch
(110/220V)
5 - ON/OFF switch
6 - Power cord
7 - Control switch (Hand/Foot)
8 - Pedal Connection
9 - Bit Holders
10 - Power indicator
11 - Foot pedal
12 - Handpiece Connection
13 - Handpiece
14 - Handpiece Holder
Power
Problem
Description
Possible Cause
Solution
Motor does
not work.
Power cord not plugged in
Power cord plugged in,
Power indicator light
illuminated,
Handpiece will not turn on.
Overload protection
has been triggered.
Unplug and re-connect
power cord from outlet.
Bad connection from
control box to pedal.
Handpiece connection
cable damaged.
Contact your dealer.
Carbon brushes worn out.
Replace carbon brushes,
or contact your dealer.
Motor works
Unable to adjust speed.
Faulty control box.
Contact your dealer.
HANDPIECE
Problem
Possible Cause
Solution
Handpiece does not work, even
if the chuck is locked.
Contact your dealer.
Handpiece starts, then stops. Faulty bearing.
Contact your dealer.
Loud noise and vibration while
in use.
Faulty bearing or collet chuck.
Contact your dealer.
Bent or broken bit. Replace the bit.
Faulty bearing, carbon brushes,
or control box.
Dealer:
MASHA’S NAILS SHOP
Tel. +1 (714) 204-5993 (WhatsApp ) |
mail@4nails.us
www.4nails.us
Date of purchase:
Serial number:
Plug power cord into outlet.
Blown Fuse
Check and replace fuse
if necessary.
Check the handpiece
connection at the control
box.
Check the pedal
connection at the control
box.
Thank you for your purchase!
Proper maintenance and repairs will ensure years of trouble-free service.
Save this manual for future reference.
Saeshin is not responsible for accidents caused by not following the instructions.
Appearance and specifications are subject to change without further notice. Users are responsible for safe operation
and maintenance. By reporting the product, model and type of failure you can expect advice and fast service from your
dealer.
105L
120
0-40,000
RPM
0-35,000
RPM
3 Ncm
3 Ncm
4
ON/OFF switch is in the ON
position; power light is not
illuminated.
Bad connection from
control box to handpiece.
Common Problems and Solutions
CONTROL BOX
5 ⅛ x 5 ½ x 3 ¼ in
( 13х13,5х8,5 cm )
7 oz
( 190 g )
6 oz
( 164 g )
6 in
( 153 mm )
5 in
( 129 mm )
2.8 lb
( 1.3 Kg )
65 W

Summary

Specifications

Component Overview

Speed control knob

Controls the rotation speed of the handpiece.

Control box

The main unit housing the motor control and power supply.

Forward;Reverse (FWD;REV) switch

Changes the direction of rotation of the handpiece bit.

Voltage selector switch

Selects the input voltage (110/220V) for the machine.

ON;OFF switch

Turns the main unit on or off.

Power cord

Connects the unit to an electrical outlet for power.

Control switch (Hand;Foot)

Selects manual or foot pedal operation mode.

Pedal Connection

Socket for connecting the foot pedal to the control box.

Bit Holders

Provides storage for spare drill bits.

Power indicator

Illuminates to show that the unit is powered on.

Foot pedal

Allows hands-free control of the handpiece speed and operation.

Handpiece Connection

Port on the control box where the handpiece cable connects.

Handpiece

The tool that holds and rotates the drill bits.

Handpiece Holder

Stand or rest for the handpiece when not in use.

Warranty

Safety Precautions

Setup and Use

Bit Installation

Procedure for opening the chuck, inserting a bit, and securing it.

Operation

Steps for turning on the machine, adjusting speed, and changing rotation direction.

Strong 210 Specifications

General

Brand	Strong
Model	210
Category	Personal Care Products
Language	English