Strong FS Series - User Manual

Product Data Sheet
© 2014 Strong
TM
Racks Rev: 140721-1700
FS SERIES
Fully Assembled Rack System w/ Integrated Cooling
SR-FS-SYSTEM-42U
Product Overview
Package Contents
A Top Cover
B Welded Frame
C Front Door - Tinted Glass
D Side Panel (x2)
E Rear Panel
F Bottom Cover
G 2U Rack Shelf (x8)
H 2U Vented Panel (x8)
I Low-ProleFine-FloorCasters(x4)
J AC Fans (x2)
K Locking Door Latch
L Door Latch Plate
M Ground Studs (x4) (located on top and
bottom covers in the rear of rack)
N Nylon Washers (x3)
O Pre-installed Bushings (x3)
Key Features
• 1000 lbs. max load capacity
• Tamper resistant lock on reversible tempered
glass front door
• Removable side and rear panels for easy
serviceability
• Front and rear rails tapped with 10/32
threads to allow for mounting of components
in front or rear of rack
• Superb ventilation system - Strategically
placed fans* & vents to ensure that
equipment stays cool
• Lowprole,neoor,lockingcasters
• Fits through a standard doorway even with
the casters on
• Lifetime limited warranty
*Notes: Fans are always on, we recommend they
are plugged into a switching surge
protector or AV receiver.
Please be sure to check with local
authorities in regard to code
requirements for compliance.
If the door is rubbing against the base,
then add the necessary amount of nylon
washers (N) onto the bottom hinge pin
to allow for extra clearance.
CAUTION!
Whenloadingequipmentintocabinet,ensurethat
thecastersarelocked,andloadheavierequipment
at the bottom of the rack.
Reversing Front Door
Tools Required:
#2 Phillips Head Screwdriver
Reversal Steps
1. Removebothsidepanels(D),andopenthefrontdoor(C).
2. Remove the Door Latch (K) by removing the clamp with a
#2Phillipsscrewdriver,andslidethelatchoutofthedoor.
3. Remove the Latch Plate (L) using a #2 Phillips screwdriver.
4. Pull the top and bottom hinge pins out of the locking
position and slide the door up and out. Remove the
bottom,pre-installedbushing(O).
5. Insert the bushing into the opposite bottom hinge pin hole.
6. Flipthedoorover,alignthebottomhingepinoverthe
grommet,andslideintoplace.Repeatforthetophingepin.
7. Attach the Latch Plate (L) to the rack opposite the door
hinges using a #2 Phillips screwdriver.
8. InserttheDoorLatch(K)intothedoor,andsecurewiththe
clamp using a #2 Phillips screwdriver.
9. Closeandlatchthedoor,andreattachthesidepanels(D).
B
A
C
D
E
F
G
H
I
J
K
L
M - Ground Studs (not shown)
N - Nylon Washers (3) (not shown)
O - Pre-installed Bushings (3)

Summary

Product Overview

Package Contents

Lists all included components of the FS Series rack system, including covers, frame, panels, shelves, casters, fans, and hardware.

Key Features

Highlights load capacity, tamper-resistant lock, serviceability, rail threading, ventilation, low-profile casters, doorway fit, and warranty.

Reversing Front Door

Tools Required

Specifies the #2 Phillips Head Screwdriver as the only tool needed for the front door reversal process.

Reversal Steps

Provides detailed, numbered instructions for removing and reattaching the front door, including latch and hinge adjustments.

Dimensions

Lifetime Limited Warranty

Details the Lifetime Limited Warranty for Strong™™ products, covering parts and labor for defects under normal use.

Strong FS Series Specifications

General

Brand	Strong
Model	FS Series
Category	Enclosure
Language	English