To Next PageTo Next Page
Need help?Do you have a question about the Strongway 46443 and is the answer not in the manual?
General| Brand | Strongway |
|---|---|
| Model | 46443 |
| Category | Outdoor Cart |
| Language | English |
Read and understand all instructions. Failure to follow may result in serious injury.
Do not allow persons to operate or assemble until they have read this manual and understand how it works.
Manuals cannot cover all situations. Operator must supply common sense and caution.
Keep work area clean and dry. Damp or wet areas can result in injury.
Keep children away from work area. Do not allow children to handle this product.
Store idle equipment in a dry location, locked up, and out of reach of children.
Use the right tool for the job. Do not modify equipment or use for unintended purpose.
Check for damaged or worn parts before use. Replace or repair immediately.
Keep proper footing and balance at all times to prevent tripping or injury.
Do not modify the cart in any way. Unauthorized modification may impair function and safety.
Always check for damaged or worn parts before using. Replace or repair immediately.
Store idle dump cart in a secure place out of children's reach. Inspect before re-use.
Do not at any time carry passengers sit or stand on the cart.
Do not exceed maximum load capacity of 1200 lbs.
Avoid large holes and ditches when transporting loads.
Be careful when operating on steep grades; the cart may tip over.
Always operate at reduced speed in rough terrain.
Do not operate close to creeks, ditches and public highways.
To avoid injury and damage, DO NOT EXCEED 10 MPH.
Always use caution when loading and unloading the cart.
Only tow with recommended vehicles (Lawn/Garden Tractors and ATVs).
Always secure and lock dump cart to the vehicle hitch before operating.
Attach support tubes to bottom panels using M8x40 screws and M8 nylon lock nuts.
Attach tongue supports I and II to bottom panels using M8x50 screws and M8 nylon lock nuts.
Attach wheel axle support stands to bottom panels using M8x20 hex bolts and M8 nylon lock nuts.
Center hitch tongue assembly in wheel axle support and insert axle through holes.
Secure wheels to axle using Ø20 flat washers and Ø4 R-pin.
Attach left and right side panel assemblies to the bottom panel using four hinge pins.
Attach front panel to bottom panel and secure using two hinge pins.
Slide rear panel through slots on the back side panels to lock it in place.
Insert side rails into side panels and secure front rail with R pins.
Guidelines for safe and effective operation of the dump cart.
Never tow the utility dump cart with the box raised.
Do not overfill the dump cart. Overflow loads can cause loss of traction.
Only fill the dump cart to a comfortable dumping load. Heavy loads are difficult to operate.
Always use the dump cart for its intended purpose.
Ensure tow vehicle and operator weight exceed load weight for proper control.
Do not use cart on public highways or roads.
Never exceed 10mph when towing the dump cart.
Do not make sharp turns that may cause tires to rub against the cart.
Always slow down before turning.
Always use caution when backing. Avoid 'jack-knifing' by backing straight.
Examine condition before use. Keep in good repair by adopting maintenance program.
After each use, clean material out of the cart box. Rinse/dry inside and outside.
Before operating, make sure tires have the RECOMMENDED TIRE PRESSURE OF 25 PSI.
Regularly grease axle and wheel bearing area. Annually clean and lightly lubricate parts.
Periodically check all fasteners for tightness.
Use glossy enamel spray paint to touch up scratched or worn painted metal surfaces.
Never exceed load capacity rating of 1200 lbs; doing so will damage the utility dump cart.
Never allow material to remain in the utility dump cart for extended periods of time.
Before storing, make sure the cart is clean and dry.
Store indoors or protected area during severe weather and winter months.
When storing outside, keep tongue higher than back to allow moisture to run out.
Diagram and list of all parts with corresponding part numbers and quantities.
