V. 3.2.5
51M
Reference guide
Remote control and
programming unit
RCC-02 and RCC-03
for the Xtender
Battery
Voltage
Real charge current
Programmed charge current
Voltage ripple
Charging phase
(bulk charge, absorption, floating charge…)
Dynamic compensation of the voltage
(compensation of threholds due to the battery internal
resistance)
Working mode (inverter, charger...)
Temperature (provided if a sensor is installed)
Compensation implied by the temperature
(provided if a sensor is installed)
Discharge of the previous day
Discharge of the current day
Input AC
Input voltage
Input current
Input power AC-In
Input frequency
Energy from AC-In of the previous day
Energy from AC-In of the current day
Output AC
Output voltage
Output current
Output power
Output frequency
Consumers energy of the previous day
Consumers energy of the of the current day
General
State of the transfer contacts
State of the inverter-charger contacts
State of the auxiliary contacts
Working mode of the auxiliary contacts
Lock states
Smart Boost active
Active sharing of the available power
(Power Sharing)
User information
Messages and account of events
Message: Too high AC-In input voltage
Message: Too low AC-In input voltage
Stop: Overload inverter SC
Stop : Overtemperature EL
Stop: Overload inverter BL
Alarm: Ventilation fault detected
Alarm: Excessive battery ondulation
Stop: Too low battery voltage
Stop: high battery voltage
Message: Power sharing exceeded;
transfer prohibited
Error: Voltage at AC Out
Error: Phase not defined
Message: Control the battery of the clock
Alarm: Overtemperature TR
Stop: Source at the output
Error: Lost of synchro master
Stop: Overload inverter HW
Alarm: Maximum duration security for
auxiliary contact
Alarm: Genset problem, no AC-In after a start by
means of the auxiliary contact
Adjustment of the remote control
Language {5000}
Other languages {5036}
Time {5001}
Date {5002}
User level {5012}
Drive the remote control to the user level basic {5019}
Backup and restoring {5013}
Backup of all files {5041}
Messages backup {5030}
Backup of remote control configurations {5015}
Backup of Xtender configurations {5017}
Load Xtender parameters preset {5045}
Loading the remote control configurations {5016}
Loading the Xtender configurations {5018}
Loading a master file {5034}
Separator of the csv files {5032}
Contrast {5006}
Back-lighting {5007}
Back-lighting always off {5008}
Duration of the back-lighting {5009}
Red back-lighting if Xtender OFF and default
{5026}
Inactivity period before returning to standard
display {5010}
Duration of display for quick messages {5011}
Accoustic alarm {5027}
Quick start guide
Setting of the language
To begin, set your remote control RCC for a display
of the information in English.
The basic display is:
Press 1 time on the key
“arrow downwards” to
display the following screen:
Once beyond this screen
you can come back to it by
means of the key ”arrow upwards”.
Press the key SET to enter
the remote control settings.
The screen of the language
choice appears.
Press once more the key SET
to modify the current
language.
The language then appears
in reverse video.
With the keys “arrow upwards” and “arrow
downwards” choose the language you wish. Then
validate your choice by means of the key SET (OK).
We can now leave the setting of the remote
control with the key ESC.
Adaptation to the source
It is a matter of indicating to the Xtender the
power available to charge the batteries and to
supply the users. In order to adapt your
installation to the source it is connected to,
proceed as follows:
The basic display is:
Press 2 times on the key
“arrow downwards” to
display the following screen:
Once beyond this screen
you can come back to it by
means of the key ”arrow upwards”.
Press the key SET to access
to the settings.
Then again on the key SET
to access to the basic
parameters.
Press the key SET to modify the value of this
parameter (it appears in reverse video).
By means of the keys “arrow upwards” and “arrow
downwards” change the value to adapt it to your
source and validate your setting with the key SET
(OK).
Adaptation to the battery
(Charge current {1138})
In order that your Xtender manages the best
possible the energy stored in your batteries and
that it charges them optimally, it is necessary to
indicate the current which they can be charged
with. You will find this value in the technical data
provided by your batteries manufacturer.
The basic display is:
Press 2 times on the key
“arrow downwards” to
display the following screen:
Once beyond this screen
you can come back to it by
means of the key ”arrow upwards”.
Press the key SET to access
to the settings.
Then again on the key SET
to access to the basic
parameters. With the key
“arrow downwards”,
access the setting “Battery
and charger cycle”.
You are now going to set
the charge current for the
batteries:
Press the key SET to modify the value of this
parameter (it appears in reverse video). With the
keys “arrow upwards” and “arrow
downwards” change the value to adapt your
battery and validate your setting with the key SET
(OK).
Activation of the function Smart-Boost
If your AC-In source is limited in power, the Xtender
can work as a support and add the missing
power for your loads.
First of all, check that you have adapted the
Xtender to your source (see previous chapter:
Adaptation to the source {1107})
The basic display is:
Press 2 times on the key
“arrow downwards” to
display the following screen:
Once beyond this screen you
can come back to it by
means of the key ”arrow upwards”.
APress the key SET to access
to the settings.
Then again on the key SET
to access to the basic
parameters. Press 2 times on
the key “arrow downwards”.
You reach now the
parameter for authorization of the Smart-Boost
function {1126}.
You can now authorize the
function. Press the key SET to
access this parameter in
modification mode, then the
keys UP or DOWN to change
the option. To end up, validate with the key SET.
Alarm: Low battery voltage
Message: AC IN synchronization in progress
Message: Wrong AC-In input frequency
To Next Page
Need help?
General
