sugar-valley Vistapool

To Next Page

VISTAPOOL CONTROL SYSTEM

INSTALLATION GUIDE 2016

Our modules allow connection remote control of all our

devices via the Internet.

The client monitors, controls and adjusts all components

and parameters of the pool from anywhere in the world.

Professional pool maintenance controls all of them remotely.

The pool automatically generates statistics about the history

of its parameters.

The WIFI Module must be within the

scope of coverage of the wireless

network that will be connected.

WIRELESS NETWORK

COVERAGE

WIFI NETWORK REQUIREMENTS AND RECOMMENDATIONS

DHCP AUTOMATIC IP ASSIGNMENT

The DSL router has to be conﬁgured to enable this service for new connections. The WIFI module uses this protocol to automatically obtain an IP address from the router. If you have experienced problems with your WIFI Module

conﬁguration and the box does not automatically connect to the router, check if DHCP is enabled. To do so, enter the router web address with a web browser (it is usually 192.168.1.1 or 192.168.0.1) and gain access to the control

panel by setting the user and password required by the router. Enter the DHCP option and enable it. Finally save and apply the conﬁguration change to let the router work with the new conﬁguration.

WIFI ENCRYPTION

Swimming pool water ﬁltering is a very delicate operation, and its control must have a certain degree of protection against unwanted access and even malicious intrusions. Therefore it is strongly recommended to use a strong

encryption protocol when installing a swimming pool connection using the WIFI network. Several tests and documents have shown that WEP encryption have some security ﬂaws and therefore should be replace it with WPA

encryption protocol. Nevertheless, many homes and companies still uses WEP encryption. If you have WEP as encryption protocol, change it by connecting to the router control panel, as explained in the previous section. Then enter

“Wireless settings” and change the WEP encryption to WPA. You can always use the same password as in the WEP encryption. Always remember to erase and create again your wireless network connection on your PC.

WIFI MODULE CONFIGURATION

2.5

2.6

2.3 2.4

2.7 2.9 2.102.8

12:30

25º

man

oﬀ

man

oﬀ

CoverPol 1

LOW

gr/h

hydrolysis / electrolysis

Pr onPol 1

Pol 2

250

7.5 OFF

AL37.0

7.2

700 OFF

AL3FL1

700

ppm

1.00

FL2

FL1

1.00

Cu/Ag ionization

measures

1 2 3 4

TANK

2.22.1

red (12V)

green (COM-B)

black (GND)

yellow (COM-A)

• Turn off the device by pressing the ON/OFF

switch and disconnect it from the plug.

• Take off the connectors lid using a screwdriver.

• Plug the WIFI Module into the corresponding

connector (WIFI) of the electronic circuit, with

the red wire positioned at the top.

• If the WiFi Module is properly connected, one

of the green LEDs will blink and the other will

remain on.

Once the WIFI module is connected, restart your unit. In the System Settings menu will appear the Network option.

pantalla 2.4 WIFI: Select WIFI to scan the available networks accessible to the module. The search will be done automatically.

pantalla 2.5 Select the desired network accessible to the WIFI module.

pantalla 2.6 Enter the password in the pop-up keyboard. Scroll up and down with the up/down keys and left to right with the

plus/minus keys. To select a letter press the OK.

pantalla 2.7 Conﬁguration: For a more detailed conﬁguration enter this menu or contact your installer.

pantalla 2.9 Status: Check the status of your connection.

pantalla 2.10 Test connection: Check that your connection has been successfully established..

INTRODUCTION

Need help?

Do you have a question about the sugar-valley Vistapool and is the answer not in the manual?

The Vistapool Control System is a sophisticated device designed to manage and automate various aspects of a swimming pool, offering comprehensive control and monitoring capabilities. This system aims to simplify pool maintenance and operation by integrating multiple functions into a single, user-friendly interface.

Function Description

The primary function of the Vistapool Control System is to allow users to remotely adjust and control all components and parameters of their pool from anywhere in the world. This includes managing filtration, lighting, sound, auxiliary relays, and electrolysis. The system also automatically generates statistics about the history of its parameters, providing valuable insights into pool performance and usage patterns. This remote control capability is facilitated through a Wi-Fi module, which connects the device to the internet, enabling access via a web interface or a dedicated application.

The system's core functionalities encompass:

Filtration Control: Users can manage the pool's filtration system, including setting schedules and operating modes (e.g., auto, manual, off).
Lighting Management: The system allows for control over pool lighting, enabling users to turn lights on/off and potentially adjust settings if compatible.
Sound Control: If integrated with a sound system, the Vistapool device can manage audio outputs.
Auxiliary Relays: The system provides control over auxiliary relays, which can be used to manage other pool equipment or features not directly integrated into the main system.
Electrolysis Management: For pools equipped with salt chlorinators, the system can control and monitor the electrolysis process, ensuring proper sanitization.
Parameter Monitoring and Statistics: The device continuously monitors various pool parameters and automatically generates historical statistics. This data can be viewed in chart format, providing a visual representation of trends and performance over time.
Remote Access: Through its Wi-Fi module, the system offers remote access, allowing users to control and monitor their pool from any internet-connected device.

Important Technical Specifications

While specific technical specifications like power consumption, operating voltage, or physical dimensions are not explicitly detailed in the provided excerpts, several key technical aspects can be inferred:

Connectivity: The system relies on a Wi-Fi module for internet connectivity. It supports DHCP for automatic IP address assignment and allows for manual configuration of network settings (IP address, subnet mask, gateway, DNS).
Network Requirements: The device requires a stable Wi-Fi network connection to function optimally. The manual emphasizes the importance of a strong Wi-Fi signal at the installation location.
User Interface: The system features an on-device display with a graphical user interface (GUI) for local control and configuration. This interface includes menus for main functions, settings, system information, and power module details.
External Connections: The device includes multiple external connections, such as a power input, a Wi-Fi module connection, and various connectors for pool equipment (e.g., filtration, lighting, auxiliary relays). The Wi-Fi module connects via a dedicated port, often indicated by a red wire.
Data Storage: The system stores historical data and statistics, which can be accessed and viewed by the user. The capacity and retention period for this data are not specified but are crucial for long-term monitoring.
Security: The system incorporates security features for remote access, including a password-protected registration process and the ability to change passwords. The manual also highlights the importance of network security, recommending WPA2 encryption for Wi-Fi networks.

Usage Features

The Vistapool Control System is designed for ease of use, offering several features that enhance the user experience:

Intuitive On-Device Interface: The device's GUI allows for straightforward navigation through menus such as "Main menu," "Settings," "System info," and "Power module." Users can configure network settings, adjust pool parameters, and view system status directly from the device.
Remote Configuration and Control: Users can access and control the system via a web interface (e.g., vistapool.es) from any internet-connected device. This enables remote adjustment of filtration schedules, lighting, electrolysis, and other parameters.
Registration Process: To enable remote access, users must register their device on the Vistapool website. This involves entering a unique "Node ID" and a password, ensuring secure access to their pool's control system.
Statistical Data Visualization: The system presents historical data in easy-to-understand charts, allowing users to visualize trends in pool parameters over time. This feature is valuable for optimizing pool operation and identifying potential issues.
User Profiles: The system supports the creation of user profiles, allowing for personalized settings and potentially managing multiple pools from a single account. Users can add new pools, fill out pool information, and save changes.
Firmware Updates: While not explicitly detailed as a user-initiated feature, the system's connectivity suggests the possibility of firmware updates to introduce new features or improve performance.
Troubleshooting Assistance: The manual provides guidance for troubleshooting common issues, such as network connectivity problems, and offers solutions like checking Wi-Fi signal strength and verifying network configurations.

Maintenance Features

The Vistapool Control System incorporates features that contribute to easier maintenance and long-term reliability:

Self-Diagnosis and Status Indicators: The device includes LED indicators (green and red) that provide visual feedback on its operational status. For instance, a green LED indicates a proper Wi-Fi module connection, while a red LED might signal an issue.
Network Status Monitoring: The system allows users to check the status of their network connection, including Wi-Fi signal strength, which is crucial for maintaining remote access.
System Information Access: Users can access detailed system information, including the firmware version and power module details, which can be helpful for troubleshooting and support.
Password Management: The ability to change passwords for both the device and the web interface enhances security and allows users to maintain control over access.
Data Logging: The automatic generation and storage of historical data on pool parameters serve as a valuable maintenance tool. This data can help identify patterns, predict potential equipment failures, and optimize maintenance schedules.
Remote Diagnostics (Implied): With remote access, it's implied that support personnel could potentially perform remote diagnostics or assist users with troubleshooting without needing to be physically present at the pool.
Modular Design (Implied): The mention of a "Power module" suggests a modular design, which could simplify repairs or replacements of specific components if needed.

In summary, the Vistapool Control System is a comprehensive solution for modern pool management, emphasizing remote control, data-driven insights, and user-friendly operation to provide a seamless and efficient pool ownership experience.