Summit Appliance SPRF34D

Questions and Answers

D
Dustin AliAug 14, 2025
What to do if my Summit Appliance SPRF34D Refrigerator is not cold enough?
- S
  Susan RamirezAug 14, 2025
  If your Summit Appliance Refrigerator isn't cold enough, several factors could be the cause. First, check if the temperature is set correctly and adjust it to a lower setting if needed. Ensure that the drawers are not opened too often and are always closed completely to maintain the internal temperature. Inspect the drawer seal for any damage or dirt, and clean or replace it if necessary. Clean the condenser when necessary, and make sure the ventilation opening is not blocked or dusty. Clear any obstructions and clean off any dust present.
J
Jennifer RobinsonAug 17, 2025
Why is my Summit Appliance SPRF34D not working?
- T
  Taylor WatsonAug 18, 2025
  If your Summit Appliance Refrigerator isn't operating, there are a few potential reasons. First, ensure the appliance is properly connected to a power supply. If it's connected, check if the appliance is switched on. Also, verify your circuit breaker hasn't tripped or a fuse blown; if so, reset the breaker or replace the fuse.
J
Joshua PattersonAug 21, 2025
What to do if my Summit Appliance SPRF34D turns itself on and off frequently?
- A
  Anthony HardingAug 21, 2025
  If your Summit Appliance Refrigerator is turning on and off frequently, it could be due to several reasons. The room temperature might be higher than average, so consider placing the appliance in a cooler location. If you've recently added a large amount of food, allow the appliance some time to reach the set temperature. Avoid opening the drawers too often and ensure they are closed completely. Also, check the drawer seal and clean or replace it if it's not sealing properly.
S
Stephanie DelacruzAug 25, 2025
What to do if the alarm sounds and the temperature display flashes on my Summit Appliance SPRF34D Refrigerator?
- Y
  ysmithAug 25, 2025
  If the alarm sounds and the temperature display flashes on your Summit Appliance Refrigerator, ensure the drawers are not opened too often, and the ventilation opening is not covered or dusty. Clear any obstructions and clean off any dust. If there has been a lengthy power interruption, allow the appliance to work for a while until it reaches the set temperature. Also, make sure that the drawer is properly closed.
M
Melissa BaileyAug 27, 2025
How to fix vibrations in my Summit Appliance SPRF34D?
- N
  Nathan WilliamsAug 28, 2025
  To fix vibrations in your Summit Appliance Refrigerator, level the appliance using the adjustable feet.
W
Wanda RobinsonAug 31, 2025
Why won't the drawers close on my Summit Appliance SPRF34D?
- F
  fbakerAug 31, 2025
  If the drawers on your Summit Appliance Refrigerator won't close, it could be due to a few reasons. First, ensure the appliance is properly leveled using the adjustable feet. Also, check if the gaskets are dirty and clean them. Finally, verify that the racks or bins are correctly positioned inside the refrigerator and refit them if necessary.
I
imasonSep 3, 2025
What to do if the light does not work in my Summit Appliance SPRF34D?
- D
  dustinhawkinsSep 3, 2025
  If the light in your Summit Appliance Refrigerator isn't working, first ensure the appliance is connected to a power supply. Then, check if a circuit breaker has tripped or a fuse has blown, and switch on the breaker or replace the fuse if needed. Finally, check the control panel to see if the light was switched off, and if so, switch it on.
R
Rachel RushSep 7, 2025
What does it mean if the icon “--” is lit and flashing in the temperature display of my Summit Appliance Refrigerator?
- D
  Dr. Tony Carpenter MDSep 7, 2025
  If the icon “--” is lit and flashing in the temperature display of your Summit Appliance Refrigerator, it means the display temperature is out of range. For SPR626OS2D, only temperatures within 0~99°F/-9~37°C can be displayed, and for SCFF51OS2D, the range is -49~99°F/-45~37°C.
A
adamestesSep 10, 2025
What does display “E0”, “E1”, “E2”, “E3”, “E4”, “E5” or “E7” mean on my Summit Appliance SPRF34D?
- S
  smallsamanthaSep 10, 2025
  If your Summit Appliance Refrigerator displays “E0”, “E1”, “E2”, “E3”, “E4”, “E5” or “E7”, call for service. “E0” indicates a communication error for 3 zone models. “E1” or “E2” indicates a failure of the air temperature sensor. “E3” or “E4” indicates a failure of the defrost sensor in the evaporator. “E5” indicates defrost heater failure. “E7” indicates door switch failure.

Summary

Appliance Safety

Important Safeguards

Essential safety precautions for operating the appliance, including electrical and fire hazards.

Safety Alert Symbols Explained

Definitions and implications of DANGER and WARNING alerts to prevent injury.

Installation Instructions

Appliance Placement and Ventilation

Electrical Connection Requirements

Specifics on grounding, outlet type, voltage, and cord safety for operation.

Anti-Tip Bracket Installation

Steps to secure the appliance against tipping hazards for child safety.

Operating Your Appliance

Control Panel and Temperature Settings

How to use the control panel and adjust temperature settings for each compartment.

Unit Operation Modes

Care and Maintenance

Cleaning Procedures

Troubleshooting

Common Operating Problems

Solutions for issues like appliance not operating or not cooling properly.

Error Codes and Alarm Indicators

Summit Appliance SPRF34D Specifications

General

Type	Refrigerator
Brand	Summit Appliance
Model	SPRF34D
Cooling System	Compressor
Defrost Type	Automatic
Energy Star Rated	No
Door Swing	Right
Shelf Type	Glass
Shelves	2
Door Bins	3
Crisper Drawer	Yes
Freezer Shelf	1
Voltage	115V
Frequency	60 Hz
Amperage	1.5 A
Height	33.5 inches
Temperature Range	32°F to 50°F

Summit Appliance SPRF34D - User Manual

Table of Contents