Summit Commercial BIM-44 G

Questions and Answers

J
Jerry BakerAug 15, 2025
What to do if my Summit Commercial BIM-44 G Ice Maker stops suddenly?
- T
  Timothy LopezAug 15, 2025
  If your Summit Commercial Ice Maker stops suddenly while making ice, there are a few potential causes. First, check if the electricity is off and reconnect the power supply line if needed. Second, the room temperature might be out of the recommended range; if so, disconnect the ice maker until the temperature returns to normal. Finally, the ice storage bin might be full, in which case you should remove some ice and ensure the ice-full probe is free of ice.
J
Jake CobbAug 19, 2025
Why is my Summit Commercial BIM-44 G leaking water?
- D
  David HouseAug 19, 2025
  There could be several reasons why your Summit Commercial Ice Maker is leaking water. If water falls to the floor when opening the door to remove ice, it's likely normal condensation. Check if the water supply connection is leaking and tighten the fitting if necessary. Also, ensure the drain pipe is lower than the drain outlet.
A
Ashley MillerAug 21, 2025
What to do if water doesn't feed into my Summit Commercial BIM-44 G Ice Maker?
- M
  Maria EllisAug 22, 2025
  If water isn't feeding into your Summit Commercial Ice Maker after it starts, check that the water supply tap is turned on. Also, make sure the water supply pipe is properly connected; if not, reconnect it.
R
Ronald WilliamsAug 26, 2025
Why does scaling occur frequently inside my Summit Commercial BIM-44 G Ice Maker?
- T
  Tammy StoutAug 26, 2025
  If scaling occurs frequently inside your Summit Commercial Ice Maker, it's likely that the hardness level of the water is too high. Consider installing a water-softening device in front of the water inlet.
C
Cory JordanAug 28, 2025
Why my Summit Commercial BIM-44 G doesn’t operate?
- K
  Kiara HaleAug 29, 2025
  There are several reasons why your Summit Commercial Ice Maker might not be operating. It could be unplugged, so ensure it is properly plugged in. The fuse might be blown, in which case you should replace it; if this happens repeatedly, call for service. Also, check that the power button is switched to the 'ON' position. Lastly, if the ice storage bin is full, remove some ice to ensure the ice-full probe is not obstructed.
B
Bryan FreemanAug 31, 2025
Why my Summit Commercial Ice Maker makes ice, but the bin doesn't fill?
- C
  Charles GreeneAug 31, 2025
  If your Summit Commercial Ice Maker is making ice, but the bin isn't filling up, it could be due to a few reasons. The condenser might be dirty, so try cleaning it. Additionally, the airflow to the ice maker might be obstructed, so check the installation. High ambient and water temperatures, or proximity to a heat source, can also cause this issue, so review the installation.
W
William OrtizSep 4, 2025
Why are my Summit Commercial BIM-44 G Ice Maker's ice cubes partially formed?
- C
  Carmen ArmstrongSep 4, 2025
  If the ice cubes from your Summit Commercial Ice Maker are partially formed or white on the bottom, it could be due to insufficient water in the water trough. Check if the water supply pressure is below 15 psig. Also, the water supply or filter may be restricted. Finally, check for a water leak at the water trough.
S
Stacey YoungSep 7, 2025
Why is water leaking from the ice storage bin of my Summit Commercial BIM-44 G Ice Maker?
- W
  William AdkinsSep 7, 2025
  If water is leaking from the ice storage bin of your Summit Commercial Ice Maker, it could be because the drainhole below the ice storage bin is blocked; remove the bin and clean the drainhole. Another potential cause is a kinked drain hose, or a drain hose improperly placed higher than the floor of the ice storage bin; ensure the drain hose allows unhindered drainage.
D
douglasmitchellSep 12, 2025
What to do if the body of my Summit Commercial BIM-44 G Ice Maker is electrified?
- R
  Robert LewisSep 12, 2025
  If the body of your Summit Commercial Ice Maker is electrified, the ground line might not be properly connected in the socket. Use a socket meeting the grounding requirements.