Sunbeam Alpine V series - User Manual

Warranty void if periodical maintenance is not followed.

Recommendation to use authorized dealers for servicing and advice.

Location of chassis and engine numbers for identification.

Engine specs, ignition timing, valve clearances, and carburettor data.

Gearbox ratios and front suspension settings.

Wheel base, track, length, height, width, ground clearance, kerb weight.

Fuel, oil, water capacities and specifications for lamp bulbs.

Diagram and listing of controls on the right-hand drive facia panel.

Diagram and listing of controls on the left-hand drive facia panel.

Operation of ignition, side/headlamp, dip switches.

Operation of direction indicators and overdrive switch.

Operation of horn, map lamp, and interior lamp switches.

Explanation of warning lamps, oil pressure, fuel, water temperature, and revolution indicators.

Description of choke, gearshift lever, and gear usage.

Operation of accelerator, brake, and clutch pedals.

Operation of the handbrake and bonnet release mechanism.

Seat adjustment and footwell ventilation control.

Operation of door locks, ignition, and baggage keys.

Access to boot, spare wheel, fuel filler cap, and tool compartment.

Information on available special accessories.

Instructions for safely using the lifting jack.

Procedures for removing and refitting pressed steel and wire wheels.

Procedures for starting cold, warm, and hot engines.

Importance and method of running-in a new vehicle.

Importance of regular lubrication and recommended lubricants.

Use of service vouchers and recommendations for engine oil.

Lubrication for engine, distributor, carburettor, fuel pump, and steering unit.

Lubrication for gearbox, overdrive, rear axle, hubs, and brakes.

Draining, refilling, and maintenance of the cooling system.

Recommendations for using anti-freeze solutions.

Procedure for adjusting valve clearances when the engine is warm.

Procedure for checking and adjusting ignition timing.

Servicing of air cleaners and silencers.

Procedure for slow running and synchronising carburettors.

Procedure for topping up carburettor damper bores.

Cleaning the fuel pump gauze filter.

Procedure for renewing the oil filter unit.

Servicing the regulator and flame trap.

Checking and topping up the steering box oil.

Procedure for checking and refilling engine oil.

Removable chart for lubrication intervals.

Engine, cooling system, tyres, and electrical checks.

Engine, clutch, brakes, transmission, axle, steering, and electrical maintenance.

Additional service items including air cleaners and front hubs.

Engine tune, cooling system, brakes, suspension, and body checks.

Engine, cooling system, electrical, and exhaust system checks.

Step-by-step guide to lowering the soft top.

Instructions for folding and securing the hood in the stowage compartment.

Steps to prepare for raising the soft top.

Instructions for securing the hood and its covers.

Warranty void if periodical maintenance is not followed.

Recommendation to use authorized dealers for servicing and advice.

Location of chassis and engine numbers for identification.

Engine specs, ignition timing, valve clearances, and carburettor data.

Gearbox ratios and front suspension settings.

Wheel base, track, length, height, width, ground clearance, kerb weight.

Fuel, oil, water capacities and specifications for lamp bulbs.

Diagram and listing of controls on the right-hand drive facia panel.

Diagram and listing of controls on the left-hand drive facia panel.

Operation of ignition, side/headlamp, dip switches.

Operation of direction indicators and overdrive switch.

Operation of horn, map lamp, and interior lamp switches.

Explanation of warning lamps, oil pressure, fuel, water temperature, and revolution indicators.

Description of choke, gearshift lever, and gear usage.

Operation of accelerator, brake, and clutch pedals.

Operation of the handbrake and bonnet release mechanism.

Seat adjustment and footwell ventilation control.

Operation of door locks, ignition, and baggage keys.

Access to boot, spare wheel, fuel filler cap, and tool compartment.

Information on available special accessories.

Instructions for safely using the lifting jack.

Procedures for removing and refitting pressed steel and wire wheels.

Procedures for starting cold, warm, and hot engines.

Importance and method of running-in a new vehicle.

Importance of regular lubrication and recommended lubricants.

Use of service vouchers and recommendations for engine oil.

Lubrication for engine, distributor, carburettor, fuel pump, and steering unit.

Lubrication for gearbox, overdrive, rear axle, hubs, and brakes.

Draining, refilling, and maintenance of the cooling system.

Recommendations for using anti-freeze solutions.

Procedure for adjusting valve clearances when the engine is warm.

Procedure for checking and adjusting ignition timing.

Servicing of air cleaners and silencers.

Procedure for slow running and synchronising carburettors.

Procedure for topping up carburettor damper bores.

Cleaning the fuel pump gauze filter.

Procedure for renewing the oil filter unit.

Servicing the regulator and flame trap.

Checking and topping up the steering box oil.

Procedure for checking and refilling engine oil.

Removable chart for lubrication intervals.

Engine, cooling system, tyres, and electrical checks.

Engine, clutch, brakes, transmission, axle, steering, and electrical maintenance.

Additional service items including air cleaners and front hubs.

Engine tune, cooling system, brakes, suspension, and body checks.

Engine, cooling system, electrical, and exhaust system checks.

Step-by-step guide to lowering the soft top.

Instructions for folding and securing the hood in the stowage compartment.

Steps to prepare for raising the soft top.

Instructions for securing the hood and its covers.