SuperFlow MV89 - User Manual

MV89
PORTABLE AIR COMPRESSOR
Owner’s Manual
PLEASE READ THIS MANUAL CAREFULLY
BEFORE
OPERATING YOUR AIR
BEFORE
OPERATING THE UNIT, IF YOU
HAVE ANY QUESTIONS, PLEASE CONTACT
US FIRST AT:
Q Industries Inc
401 East Las Olas Blvd., Suite 130
Fort Lauderdale, Florida 33301
P: 954.689.2263 F 303.568.7700
E Mail: Customerservice@qindustries.net
www.superflowair.com
SPECIFICATIONS
Motor: 12-Volt DC
Maximum working pressure: 120psi.
Maximum re-start pressure: 90psi.
Maximum continuous operating time is 40 minutes.
Overheating Protection Circuit:
The unit is equipped with an automatic protection
device. In the event the unit reaches an unsafe
operating temperature, a protection circuit will cut
power to prevent damage to the unit. If the protection
circuit activates, immediately disconnect the unit from
the power source and allow it to cool.
The unit will cool in approximately 15 minutes,
depending on environmental conditions. The protection
circuit will automatically
reset itself when the
temperature returns to a safe operating level.
High altitude and certain air temperatures can negatively
affect the unit’s performance.
WARNING:
WARNING! READ ALL INSTRUCTIONS before
operating product. Failure to follow all instructions
below may result in electrical shock, fire and
serious injury or death.
WARNING! Always wear ANSI Z87.1 approved safety
glasses with side shields when operating.
Compressed air and particulate matter can cause
eye and soft tissue damage. Keep air stream away
from skin and eyes
WARNING! RISK OF BURNS:
Always wear
gloves. Some exposed parts may become hot
during use.
WARNING! RISK TO BREATHING:
This
compressor is not designed for and never should
be used as a source of breathable air.
WARNING! RISK OF ELECTRICAL SHOCK:
This compressor is for use in dry conditions only.
WARNING! RISK OF FALLING: This compressor
will produce vibrations and can “walk.” Only
operate at ground level
.
WARNING! RISK OF FIRE:
This unit will become
hot during operation. Allow to cool before storing.
WARNING! RISK OF BURSTING: Use only
accessories rated for 120 psi. Always follow tire
manufacturer’s recommended inflation
instructions. In most cases they can be located on
the side wall of the tire. If you are unsure, contact
the manufacturer.
WARNING! DO NOT MODIFY: Never drill, modify
or attempt to repair the unit. There are no user
serviceable parts inside.
WARNING! SAFE HANDLING: Never carry the
unit by the hose or power cord.
WARNING! PAY ATTENTION: Do not leave the
unit running unattended.
WARNING! California Proposition 65
Warning! This product or its power cord contains
lead, a chemical known to the State of California to
cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
• Hard Mounting:
This unit may be hard mounted in a dry location. Be
sure to use proper size wiring for your application.
When using this unit with an air tank, you must install a
back-flow preventing device to prevent damage to the
cylinder head air valve.

Summary

Product Specifications

Technical Details

Details motor type, maximum working pressure, re-start pressure, and continuous operating time.

Overheating Protection Circuit

Explains the automatic protection device that cuts power to prevent unit damage.

Safety and Operational Warnings

General Safety Precautions

Read instructions, wear safety glasses, and be aware of burn and breathing risks.

Hazardous Condition Warnings

Covers electrical shock, falling, fire, bursting, modification, handling, and Proposition 65 risks.

Hard Mounting Guidelines

Instructions for securely mounting the unit and using it with an air tank.

Operating Instructions

Pre-Operation Checks

Unpack, inspect for damage, and unwrap the power cord before use.

Connecting and Powering

Connect air supply hose, attach power clips to a 12-volt source, and switch unit on.

Inflation Procedure

Screw inflator onto tire valve, monitor gauge, and stop inflation at recommended pressure.

Stopping and Restarting

Guidance on how to stop and restart inflation, especially at high pressures.

Troubleshooting and Maintenance

Troubleshooting Unit Stops

Check battery, circuit breaker, and overheating protection if the unit stops.

Resetting Circuit Breaker

Instructions on how to reset the pop-up circuit breaker after an overload.

Inflator Air Leak

Diagnose air leaks from the inflator end, checking O-rings for damage.

Storage and Care

Cool unit before storing, repack in original packaging, and store in a dry location.

Warranty Information

Product Warranty

Details the 3-year warranty, coverage, exclusions, and contact information for claims.

SuperFlow MV89 Specifications

General

Brand	SuperFlow
Model	MV89
Category	Air Compressor
Language	English