Superlift SDO-5 DC FS 1000 - User Manual

Ensure installation is performed by a technically qualified or licensed person to prevent injury or damage.

Verify garage door is properly balanced and aligned before installing AGDO for safe operation.

All garage door repairs must be conducted by technically qualified persons to avoid severe injury.

Remove or render inoperative all existing locks and ropes before AGDO installation.

Properly lubricate sectional door springs to prevent AGDO malfunction due to friction.

Install AGDO at least 2m high; adjust manual release chord to 1.8m.

Do not connect the AGDO to the power source until instructed by the manual.

Connect AGDO to a properly earthed 240V outlet installed by a qualified electrician.

Mount wall control panel within sight of the door, min 1.5m high, away from moving parts.

Install the Entrapment Warning Label prominently next to the wall control button.

Ensure the Manual Release Instruction Tag remains attached to the Manual Release Chord.

After installation, test that the door reverses upon contact with a 35mm high object.

Check the Safety Obstruction Reversing System monthly for proper function.

Never operate AGDO unless door is in full view and free from people or objects.

Never allow children to operate AGDO; always supervise them near the door.

Avoid disengaging AGDO for manual operation with persons or objects near the door.

Never open or close the garage door by pulling on the Manual Release Chord.

Disconnect power supply before making any repairs or removing AGDO covers.

Fit Safety Beams for enhanced operating safety; mandatory in some countries.

Only a technically qualified person should remove AGDO protective covers.

Always ensure the garage door is fully open before driving out and fully closed before leaving.

Adjustments to safety force settings must only be done by a qualified person.

Keep hands and loose clothing clear of the garage door and product.

The obstruction system requires force to operate, potentially causing minor damage.

Obstruction system is for stationary objects; moving objects may cause injury or damage.

Details warranty exclusions related to improper installation, usage, or maintenance.

Connect the drive rail to the power head using the provided 'U' type brackets and nuts.

Select appropriate options for attaching the drive rail hanger to the ceiling for stability.

Adjust drive belt tensioner to achieve 3-5mm sag; avoid over-tightening.

Select the correct installation method based on your garage door type from the diagrams.

Securely mount the header and door brackets to structural members of the garage and door.

Lift and attach the drive rail to the header bracket, securing with the clevis pin and clip.

Fasten the power head to a structural ceiling member, ensuring the drive rail is parallel.

Attach the bent connecting arm to the door bracket and align with straight arm, securing with bolts.

Pull the disengage chord to disconnect the AGDO from the garage door for manual operation.

Use the disengage chord and hand transmitter to re-engage the AGDO with the garage door carriage.

Ensure carriage lock, connect power, and power on the AGDO. Opener enters standby mode '11'.

Learn transmitter codes into the AGDO and how to delete all stored codes.

Configure the fully open and fully closed positions for the garage door travel.

Set the force sensitivity for the safety obstruction system (range 1-5).

Adjust the door's opening and closing speed, with 'A' being full speed.

Enable automatic door closing after a preset delay once the door is fully open.

Choose if Auto Close operates only from fully open or any open position.

Adjust the duration the AGDO courtesy light remains on after operation.

Set the height for automatic reverse function based on door travel increments.

Configure a partial opening height for the door using specific remote buttons.

Set whether one or all four remote buttons activate the AGDO.

Program the AGDO to accept a specific quantity of transmitters (5-50).

Ignore Auto Reverse for minor obstructions (e.g., snow buildup) up to a set height.

Configure the pedestrian door sensor connection (Normally Open or Normally Closed).

Install and enable the optional safety beams for enhanced safety features.

Set the AGDO to flash the courtesy light after a preset number of open/close cycles.

Utilize the UP/DOWN buttons for basic door open/close functions.

Procedure for replacing the battery in the hand-held transmitter.

Information on installing and pairing the wireless wall switch.

Procedure for replacing the battery in the wireless wall switch.