“-”position.plug the cord set into a AC220-240V~ electrical outlet,with
“BEE” sounds the “Power”light is on and the heater will shows the
default temperature ,it will twinkle 3 seconds.
1) HEATING PREPARE
Set time
Before turn on the heater,set the time as right time.Press remote control
“ ” button,light on control panel,it shows current Room temperature.
WEEK Press “Set” button one time,”I/W” lights on,press “ two
buttons set the week from 1--7 (1=Monday,2=Tuesday...7=Sunday ect.)
HOUR Press “Set” button again,”II/H” lights on, “ two buttons set
the Hours from 01--00(01=1 o’clock,02=2 o’clock...00=24 o’clock ect.)
MINUTE Press “Set” button again,”Fan/M” lights on, “ two buttons
set the Minutes from 00--59(01=1 Minute,02=2 Minute ect.)
PS:Press “Set” button,screen shows number will twinkle 5 seconds,you
should operate in time ,otherwise appliance will get back to standby.
(Appliance will keep the right time until power off)
2)General Using OPERATION
1. Turn the heater ON by pressing the ON/OFF main button ,the unit will
blow the cold air and “Fan/M” light is on.
2. Pressing the “MODE” button ,the unit will blow the warm air and
both“I/W”“Fan/M” lights are on.
3. Pressing the “MODE” button second times,the unit will blow the hot
air and both “I/W”“Fan/M” lights are on.
4. Pressing the “MODE” button Three times,the unit will blow the cold air
and “Fan/M” light is on.
PS:Control panel and remote control are same operate way.
3) 24H Timer FUNCTION
1.Open the appliance as working conditions,(fan,warm,hot are all
ok).Control panel “TIMER” button and remote control “ ” button are
same operate way.
2. Press “TIMER” button ,set the timer up to 24 hours,keep press “TIMER”
button to increase the hours from 00--24(00= close,01=1hour,02=2
hours...24=24 hours ect.) and the “TIMER” light is on.
PS:set as “00” means no set timer ,the “TIMER” light is off.
4)THERMOSTAT INSTRUCTIONS
1. Open the appliance as working conditions,(fan,warm,hot are all
ok).This function only through by Remote control.
2. To adjust temperature,press the “ ” to set the desired
temperature and the temperature set from 10℃ to 49℃.
3. When the air temperature drops 2 degree below the set temperature,the
heater will start heating with ”I/W”(1000W).
4. When the air temperature drops 4 degree below the set temperature
,the heater will start heating with”II/H”(2000W).
5. When the air temperature high 1 degree or ≤ the set temperature,the
heater will blow the cold air .
5)Week Timer FUNCTION
1.Open the appliance as working conditions,(fan,warm,hot are all ok).This
function only through by Remote control.
2.WEEK Press “ ”button 1st time,”I/W” and”W-Timer” are lights
on,show “1”means “Monday”.
HOUR Press “ ” button 2nd times,”II/H” lights on, “ two
buttons set the Hours from 01--00(01=1 o’clock,02=2 o’clock...00=24
o’clock ect.)
MINUTE Press “ ” button 3rd times ,”Fan/M” lights on, “ two
buttons set the Minutes from 00--59(01=1 Minute,02=2 Minute ect.)
---------------------------------------------------------This is open time
HOUR Press “ ” button 4th times,”II/H” lights on, “ two
buttons set the Hours from 01--00(01=1 o’clock,02=2 o’clock...00=24
o’clock ect.)
MINUTE Press “ ” button 5th times ,”Fan/M” lights on, “ two
buttons set the Minutes from 00--59(01=1 Minute,02=2 Minute ect.)
---------------------------------------------------------This is close time
The above are finised set Monday Timer.
To Next Page
Loading...
