Swim & Fun Frisbee FX2

Questions and Answers

F
Francis ReevesAug 17, 2025
What to do if Swim & Fun Vacuum Cleaner doesn't fully cover the pool floor?
- M
  Michelle McleanAug 18, 2025
  If your Swim & Fun Vacuum Cleaner isn't fully covering the pool floor, it might be due to a few reasons. First, check the wheel angle, as an improper angle can affect coverage. You may need to adjust the wheel position. Also, if the swimming pool water circulation system is on, shut it down, as this can interfere with the cleaner's path. Special pool shapes may also affect coverage, so you may need to adjust the wheel position.
M
Michelle BondAug 20, 2025
Why is my Swim & Fun Vacuum Cleaner silent or the impeller rotating after I turn it on?
- D
  Daniel GallegosAug 20, 2025
  If your Swim & Fun Vacuum Cleaner is silent or the impeller is rotating after you turn it on, it could be due to a low battery. In this case, recharge the battery. If the problem persists after recharging, it may indicate an internal fault, and you should contact after-sales service.
M
Mark HayesAug 23, 2025
What to do if Swim & Fun Vacuum Cleaner swing plate cannot stand when touching the wall?
- H
  hdavisAug 23, 2025
  If the swing plate on your Swim & Fun Vacuum Cleaner cannot stand when it touches the wall, it's possible the swing plate is stuck. Remove the cleaner from the pool and try to manually rotate the swing plate. If it remains stuck, contact the after-sales service.
A
Alex SerranoAug 26, 2025
What to do if Swim & Fun Vacuum Cleaner swing plate stands but the cleaner cannot reverse?
- A
  Ashley StevensAug 26, 2025
  If the swing plate of your Swim & Fun Vacuum Cleaner stands when touching the wall, but the cleaner won't reverse, the water channel might be stuck. Try to manually overcome the stuck condition.
J
Joseph FreemanAug 27, 2025
What to do if the Swim & Fun Vacuum Cleaner charger indicator does not work?
- J
  judy39Aug 27, 2025
  If the charger indicator on your Swim & Fun Vacuum Cleaner isn't working, the adapter may be damaged. Contact after-sales service.
C
Colleen HillAug 30, 2025
What to do if Swim & Fun Vacuum Cleaner alarms or impeller doesn't rotate when fully immersed?
- C
  Christian CampbellAug 30, 2025
  If the sound signal on your Swim & Fun Vacuum Cleaner continues to alarm, or the impeller doesn't rotate after the cleaner is fully immersed in water, it indicates an internal fault. Contact after-sales service.
A
Anita TapiaSep 1, 2025
Why doesn't my Swim & Fun Frisbee FX2 Swimming Pool Vacuum cleaner cover the entire floor?
- V
  Vernon StokesSep 1, 2025
  If your Swim & Fun Swimming Pool Vacuum isn't fully covering the floor, it could be due to a few reasons. First, check the wheel angle, as it might be improperly adjusted. See section 4.3 (Functions and adjustment methods of wheels) for instructions on how to adjust the wheel position. Another cause might be the unique shape of your pool, which also requires wheel adjustment (see section 4.3 Functions and adjustment methods of wheels). Finally, make sure your swimming pool's water circulation system is turned off, as this can affect the cleaner's coverage.
D
Devin ClaytonSep 4, 2025
What to do if the Swim & Fun Swimming Pool Vacuum swing plate cannot stand when touching the wall?
- J
  Justin VargasSep 4, 2025
  If the swing plate on your Swim & Fun Swimming Pool Vacuum doesn't stand when it touches the wall, it's likely that the swing plate is stuck. Remove the cleaner from the pool and try to manually rotate the swing plate or contact the after-sales service.
A
Alison KennedySep 6, 2025
What to do if Swim & Fun Frisbee FX2 Swimming Pool Vacuum sound signal is silent or the impeller isn't rotating after powering on?
- T
  travisturnerSep 7, 2025
  If you're experiencing a silent sound signal or the impeller isn't rotating after turning on your Swim & Fun Swimming Pool Vacuum, the battery might be low. Try recharging the battery. If the problem persists, it could indicate an internal fault, and you should contact after-sales service.
W
Whitney ShortSep 9, 2025
What to do if the Swim & Fun Swimming Pool Vacuum swing plate stands but the cleaner cannot reverse?
- M
  Mitchell SuttonSep 9, 2025
  If the swing plate can stand when the cleaner touches the wall, but the Swim & Fun Swimming Pool Vacuum cannot reverse, the water channel is likely stuck. Try to manually overcome the stuck condition.