SwitchBot Contact Sensor User Manual
1.In the Box
Note: The visuals used in this manual are for reference only. Due to the future updates and
improvements of the product, the actual product images may differ.
2.Device Instruction
3.Preparation
A smartphone or tablet with Bluetooth 4.2 or above
Download the SwitchBot app
Create a SwitchBot account and sign in
4.Installation
Remove the release paper behind the main body and the magnet, stick it on the door frame or
window frame, and press for more than 60 seconds. Note that the two parts need to be aligned
at the bottom
Installation Tips:
Make sure the sensor is not pointing to appliances or heat source in order to reduce interfer-
ence and to avoid false alarms.
The sensor senses up to 5m away and up to 90°, horizontally.
The sensor senses up to 5m and up to 60°, vertically.
5.Initial Setup
1.Remove the back lid of the sensor. Follow the "+"
and "-" marks, insert two AAA batteries into the
battery box. Put the back lid back.
Contact Sensor x 1 AAA batteries x 2 magnet x 1 Sticker x 1
LED Indicator Light and Light Sensor
Button and Fresnel Lens
2. Open the SwitchBot app and sign in.
3. Tap the "+" icon on the top right of the Home page.
4. Choose the Presence Sensor icon to add the device to your account.
6.Battery Replacement, Firmware, and Factory Reset
Battery Replacement
Remove the back lid of the sensor. Follow the "+" and "-" marks, replace the old batteries with
new ones. Put the back lid back.
Firmware
Make sure you have the up to date firmware by upgrading in time.
Factory Reset
Long press the Reset Button for 15 seconds or until the LED Indicator Light is on.
Note: After the device is reset, all settings will be set to the default values and the activity logs
will be erased.
7.Specification
Model Number：W1201500
Size：Body size 70.5*25.5*23mm，magnet size 35*12*12.5mm
Weight：Body Weight：43g，magnet Weight 13g
Power & Battery Life：AAAx2, typically 3 years
Measure Range：-10℃~60℃，20~85%RH
Maximum Detection Distance: 5m
Maximum Detection Angle: 120° horizontally and 60° vertically
8.Return and Refund Policy
This product has one-year warranty (start from the purchasing day). The situations below do not
fit the Return and Refund Policy.
Intended damage or abuse.
Inappropriate storage (drop down or soaking in water).
User modify or repair.
Using loss.
Force majeure damage (Natural disasters).
9.Contact and Support
Setup and Troubleshooting: support.switch-bot.com
Support Email: support@wondertechlabs.com
Feedback: If you have any concern or problem when using our products, please kindly send feed-
back from the Profile> Feedback page in the SwitchBot app.
10.FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.Any Changes
or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment. This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates uses and can radiate radio frequency energy and, if not installed
Magnet
and used in accordance with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the inter-
ference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is con-
nected.
-Consult the dealer or an experienced radio/TV technician for help.The device has been evaluated
to meet general RF exposure requirement. The device can be used in portable exposure condition
without restriction.
FCC RF exposure statement:
The equipment complies with FCC Radiation exposure limit set forth for uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator
and your body.
To Next Page
Need help?
General