Why is chemical liquid leaking from the escape port of my Tacmina PW Water Pump?
If chemical liquid is leaking from the chemical liquid escape port of your Tacmina Water Pump: * Replace the relief valve if it hasn't been replaced after use. * Check the pressure and specifications, as an abnormal pressure may have been generated.
Why is the discharge capacity of my Tacmina Water Pump too small?
If the discharge capacity of your Tacmina Water Pump is too small, here are several possible reasons and solutions: * Air may have entered the pump head; release the air. * The diaphragm may have deteriorated or been damaged; replace it. * The valve seat area may have deteriorated or be clogged; clean or replace it. * The pipe may be clogged; clean it. * The suction height may be outside the specified range; adjust it. * The chemical liquid may be too viscous; reduce the viscosity or change to high-viscosity joints. * The discharge pressure may be too high; check the pressure and specifications. * The stroke length may be too short; increase it. * The suction-side hose or valve may be clogged; clean or replace them. * The foot valve or the strainer may be clogged; clea...
What does error code E-02 mean on a Tacmina PW?
If E-02 is displayed on your Tacmina Water Pump, the chemical liquid remaining in the tank has dropped to a low level. Replenish the chemical liquid in the tank.
What does error code E-04 mean on a Tacmina PW?
If E-04 is displayed on your Tacmina Water Pump, the buffer size has been exceeded in the pulse input-based proportional control. Review the setting and the pump model.
What does error code E-05 mean on a Tacmina PW?
If E-05 is displayed on your Tacmina Water Pump, the analog input value has dropped below 2 mA or risen above 22 mA. Check the wiring connections.
What does error code E-06 mean on a Tacmina PW Water Pump?
If E-06 is displayed on your Tacmina Water Pump, it means the discharge pressure has increased to an abnormally high level. Return the piping pressure to the normal level.
How to unlock the keys on my Tacmina PW?
If the keys on your Tacmina Water Pump cannot be operated, release the key lock.
What to do if my Tacmina Water Pump cannot receive pulse input?
If your Tacmina Water Pump is not receiving pulse input: * Check the signal cable for disconnections. * Verify the signal input specifications are correct.
Why does the actual discharge capacity differ from the set value on my Tacmina PW?
If the actual discharge capacity of your Tacmina Water Pump differs significantly from the set value in manual mode: * The wrong maximum discharge capacity may have been set; perform calibration and set the maximum value correctly. * The stroke length may be different from when the maximum value was set; set the stroke length to the necessary value and then set the maximum value correctly.
How to troubleshoot a Tacmina Water Pump that does not turn on?
If your Tacmina Water Pump isn't turning on and the display is dark, here's what to check: * **Power Supply:** Ensure the pump is connected to the correct power supply and voltage. * **Wiring:** Inspect all wiring connections to the pump for any issues and correct them. * **Power Cable:** Check the power cable for any damage. * **Main Power:** Make sure the main power supply is properly connected. * **Breaker:** Check if the breaker has tripped; if so, find out why and reset it. * **Circuit:** There may be a circuit malfunction, in which case, replace the circuit.
Covers guidelines for installing the pump, connecting pipes, and electrical wiring.
Instructions for connecting the pump's power and grounding wires.
Essential safety guidelines and checks before, during, and after pump operation.
Methods for adjusting the pump's discharge capacity via stroke number or length.
Procedures for removing air from the pump head and lines to ensure proper function.
Function to accurately set discharge capacity by measuring actual output.
Details on various control modes like manual, timer, and pulse input for pump operation.
Configuration options for pump behavior, alarms, and operational modes via parameters.
Safety guidelines and general checks for performing maintenance tasks on the pump.
Common problems, causes, and solutions for pump malfunctions during operation.
Technical data including discharge volume, pressure, speed, and environmental ratings.
Step-by-step guide for setting up the PW series pump in standard pulse mode.
Step-by-step guide for setting up the PWM series pump in analog mode.
General| Brand | Tacmina |
|---|---|
| Model | PW Series |
| Category | Water Pump |
| Language | English |
To Next Page