Need help?Do you have a question about the TAGSYS RFID Medio L400 and is the answer not in the manual?
General| Brand | TAGSYS RFID |
|---|---|
| Model | Medio L400 |
| Category | Card Reader |
| Language | English |
Legal disclaimers and limitations of liability for the product and documentation.
Defines the intended audience for this document.
Explains symbols and formatting used in the manual.
Provides contact information for support and assistance.
Invites feedback for improving documentation.
Details how to report product defects and contact quality service.
Provides general guidelines for safe and proper use of the device.
Offers advice on how to handle and maintain the device for longevity.
Details critical safety instructions for using the device.
Specifies environmental conditions for safe and effective device operation.
Covers health and safety standards related to electromagnetic fields.
Outlines regulatory compliance for RFID systems and the Medio L400.
Details compliance with European CE and RTTE directives.
Lists FCC IDs for different antenna configurations of the Medio L400.
Provides FCC ID cross-reference for Medio L400-4 configurations.
Explains how to set uplink parameters for ISO 15693 tags in the software.
Details FCC compliance for the Medio L400 in the USA.
Specifies radio interference regulations for the device in Canada.
Addresses compliance with RoHS and WEEE directives for hazardous substances.
Provides a general introduction to the Medio L400 reader and its capabilities.
Lists the main technical features and specifications of the Medio L400.
Details the contents of the Medio L400 reader kit.
Describes the physical aspects of the Medio L400 reader.
Details the components and connectors on the front panel of the reader.
Explains the RF connectors and status LEDs on the front panel.
Describes the GPIO connector and its associated status LEDs.
Details the LCD screen and keypad functions on the front panel.
Describes the content of each page displayed on the reader's LCD screen.
Details the connectors and features on the rear panel of the reader.
Covers physical installation aspects, including mounting options.
Provides guidelines for connecting cables and power supply.
Explains how to connect and use the reader via USB.
Details the procedure for using the RS-232 serial interface.
Describes how to set up and use the Ethernet connection.
Steps to reset the reader to its factory default settings.
Guide to initially launching and using the Tagsys Explorer software.
Instructions for installing the Tagsys Explorer software on a PC.
Detailed steps for installing the Tagsys Explorer software.
Final steps and confirmation for the Tagsys Explorer installation.
Guide to connecting the reader to Tagsys Explorer via its wizard.
How to start the Tagsys Explorer wizard if it doesn't open automatically.
How to select the RFID device within the Tagsys Explorer software.
Choosing tasks like configuration or tag reading in Tagsys Explorer.
Reviewing and confirming selected parameters before applying them.
Step-by-step guide to read the UID of ISO 15693 tags using Tagsys Explorer.
Instructions for reading and writing data to ISO 15693 tag memory.
How to perform single block read/write operations on ISO 15693 tags.
Procedures for upgrading the reader's system and radio firmware.
Steps to upgrade the system firmware of the RFID reader.
Steps to upgrade the radio firmware of the RFID reader.
Describes the internal architecture and functional blocks of the Medio L400 reader.
Details the communication protocols used between the reader and the host system.
Explains the TAGSYS StxNG communication protocol and frame format.
Describes the heartbeat service for monitoring reader status over Ethernet.
Details the Telnet server functionality for reader configuration.
Explains the serial console access for reader configuration.
Information on operating the reader in standalone mode without a host.
Explains how the reader executes commands and handles operations.
Details the different read modes available for asynchronous reading.
Explains options like Multiplexer, Input triggered, and Output feedback for read modes.
Describes the types of events generated during asynchronous tag reading.
Provides examples of event sequences for tag detection and movement.
Presents a detailed table of technical specifications for the Medio L400 reader.
Details the mechanical dimensions and mounting features of the reader.
Explains the RS-232 connector pin assignment and details.
Covers the General Purpose Input/Output (GPIO) connector.
Details the pin assignments for the GPIO connector.
Lists the electrical characteristics for the GPIO pins.
Explains how to connect external sensors to the reader's inputs.
Describes how to connect external loads to the reader's outputs.
Outlines the general warranty terms and conditions for the product.
Lists conditions and situations that are excluded from the product warranty.
Provides general provisions that define the full extent of TAGSYS' warranty responsibility.
Details the procedure for returning defective products for warranty service.
To Next Page
