tahoe gear TGT-CARSON-18 User Manual

Center Tent Cabin
1. Spread the inner tent out flat, floor side down.
Tie Metal center hub G to top of center cabin.
Assemble the five black fiberglass poles(C,D,E) insert into the sleeves on the top of the tent.
The upper ends of C,D,E insert into G (center hub), and the lower ends insert into steel poles H,I,J,K,L.
Insert two grey fiberglass poles(B)into the sleeves and into steel poles H,I,J,K.(pic.2,3,4,5,6,7,8)
pic.2
pic.1
pic.3 pic.4 pic.5
pic.6 pic.7 pic.8
2.Insert the double prong steel poles ends (H,I,J,K,L) into the corresponding
pin rings (center portion of the tent).(pic.9,10)
pic.9
pic.10
Side Cabins Assembly
3.Assemble the two yellow fiberglass poles(A). Insert into side pole sleeves.
Insert fiberglass into steel single prong upright poles (M).(pic.11)
Then insert the end of poles into the corresponding pin rings.(pic.13)
4. Place inner tent's S-hook to fasten on the plastic pipe hole.Clip the plactic
hooks to the corresponding steel poles(M).(pic.12)
5. Tie the guy ropes on the center of two yellow fiberglass poles(A).Then pull
the guy ropes and stake the guy ropes into the ground.(pic.14,15)
Fix the inner tent stakes into the rings on the corners of the tent to secure it
to the ground.(pic.16,17)
7.Place the fly over the tent. Wrap the Velcro fasteners of the fly
around the fiberglass and steel poles.(pic.20,21)
8.Insert the front door steel poles into the corresponding pin rings.(pic.24,25)
9.Attach the fly to the tent by hooking the plastic S-hook on the fly
corners to the rings at the tent corners.(pic.27,31)
10. Assemble the two shortest 6.9mm fiberglass poles (F) and insert into the
sleeves on the side of the tent and the corresponding pin rings.(pic.22,23,24)
11. Fix the fly stakes into the rings on the corners of the tent to secure it
to the ground.(pic 24,25,26,27)
Meanwhile, remove 2 guy ropes which were tied on the center of two
yellow fiberglass poles(A).
12. Finally secure the tent in place with the guy ropes and extra tent stakes.
(pic.28,29)
13. Tent assembled. Front side refer to pic.24. Back side refer to pic.30
pic.18
pic.19
pic.11
pic.12
pic.13
pic.15
pic.14
pic.17
pic.16
6.To set up the front door of tent with the steel poles.(pic.18,19)

tahoe gear TGT-CARSON-18 Specifications

General

Brand	tahoe gear
Model	TGT-CARSON-18
Category	Tent
Language	English

Summary

Center Tent Cabin Assembly

Prepare Inner Tent and Center Hub

Spread inner tent flat, floor side down, and attach center hub to cabin top.

Connect Steel Poles to Pin Rings

Insert double prong steel poles into pin rings at the tent's center.

Side Cabins Assembly

Assemble Side Cabin Poles

Assemble yellow fiberglass poles into sleeves and upright poles.

Attach Inner Tent Hooks

Fasten inner tent's S-hooks to plastic pipe holes and clip hooks to steel poles.

Secure Tent with Guy Ropes

Tie guy ropes to fiberglass poles and stake them to the ground for stability.

Fly and Pole Setup Procedures

Set Up Front Door Poles

Set up the front door of the tent using steel poles.

Position and Secure the Fly

Drape the fly over the tent and secure it with Velcro fasteners around poles.

Assemble and Attach Side Fly Poles

Assemble short fiberglass poles and insert into side tent sleeves and pin rings.

Final Tent Securing

Use guy ropes and extra stakes to fully secure the tent in place.

Important Safety Warnings

Flame and Heat Source Warning

Keep all flame and heat sources away from the tent fabric.

Carbon Monoxide Danger

Do not use fuel burning devices inside or near the tent due to asphyxiation risk.

General Usage Precautions

Do not pitch near open fire, use candles, or leave children unattended.

Tent Care and Storage

Avoid prolonged sunlight exposure and do not store the tent on concrete.

Warranty and Replacement Parts

Two Year Manufacturer Warranty

Tent is covered by a two-year warranty against defects in workmanship and materials.

Exclusions from Warranty

Warranties do not cover normal wear, misuse, mildew, rotting, or UV damage.

How to Obtain Replacement Parts

Contact customer service via phone or website for missing or broken parts.