What to do if the winch pulling power is low on my Tajfun EGV 35 A?
There are several potential reasons for low winch pulling power: too much wire rope on the drum, incorrectly adjusted clutch, greasy or worn out clutch plates, a fault in the switching mechanism, or a damaged driving component. You can clean the surface or replace the clutch plates. Also, check the operation of the switching mechanism and replace any damaged parts.
What to do if the brake does not function on my Tajfun EGV 35 A?
If the brake isn't working, it could be due to an incorrectly adjusted brake, greasy brake band lining, a damaged brake mechanism, or a worn-out brake band. Clean the brake band lining and the drum surface. If needed, replace the damaged parts or the brake band itself.
Why is the winch pulling when the clutch is disengaged on my Tajfun EGV 35 A?
If the winch is pulling even when the clutch is disengaged, the cause may be an incorrectly adjusted clutch, a damaged drum, or damaged clutch plates. Replacing the drum or the clutch plate might be required.
How to fix a wire rope that is hard to pull out on Tajfun EGV 35 A?
A wire rope that's hard to pull out could be due to an incorrectly set wire rope release power, a damaged wire rope, or a damaged brake band. Replacing the brake band may solve this issue.
What to do if the brake of my Tajfun Industrial Equipment does not function?
If the brake isn't working, it could be due to several reasons. First, the brake might be incorrectly adjusted, so you should set the brake power as described in Chapter 4.5. Another cause might be that the brake band lining is greasy, in which case you should clean the brake band lining and the drum surface. Also, the brake mechanism could be damaged, requiring you to replace the damaged parts. Lastly, a worn-out brake band will need replacement.
Why is the winch pulling power of my Tajfun Industrial Equipment so low?
The winch might have low pulling power due to several reasons: * Too much wire rope on the drum (see Chapter 1.2). * Incorrectly adjusted clutch, in which case you should set the pulling power according to the instructions in Chapter 4.6. * Greasy clutch plates, which means you should clean the surface of the clutch plates or replace them. * Worn out clutch plates. * A fault in the switching mechanism (refer to Chapter 4.7 to check its operation). * Damaged driving component of the winch, which would require replacing the damaged parts.
What to do if the winch of my Tajfun Industrial Equipment is pulling when the clutch is disengaged?
If the winch is pulling even when the clutch is disengaged, it could be due to an incorrectly adjusted clutch; check the pulling power setting according to Chapter 4.6. Alternatively, the drum or clutch plates could be damaged, requiring replacement.
How to fix a wire rope that is hard to pull out on my Tajfun Industrial Equipment?
If the wire rope is hard to pull out, it might be due to an incorrectly set wire rope release power; set it according to the instructions in Chapter 4.5. It could also be due to a damaged wire rope, which would need replacing as described in Chapter 4.4, or a damaged brake band, which should also be replaced.
Details the intended uses and scope of the logging winch for agricultural purposes.
Provides key specifications like pulling power, speed, dimensions, and weight of the winch.
Explains the information found on the winch's type plate for identification.
Outlines essential safety measures, personal protective equipment, and operational rules.
Describes the procedure and checks for connecting the PTO shaft to the winch.
Explains how to release the brake to allow wire rope to be pulled off the drum.
Details the process of engaging the winch to pull and coil the wire rope onto the drum.
Instructions on how to safely release the wire rope when it is under tension.
Step-by-step guide for fitting a new wire rope onto the winch drum.
Describes how to adjust the brake power for controlled wire rope release.
Explains how to adjust the winch's pulling force for optimal performance.
Details the procedure for adjusting the brake power for safe operation.
Instructions on checking and tightening the drive chain for proper function.
Provides solutions for common problems like low pulling power or brake malfunction.
Outlines a plan for regular checks, lubrication, and component replacement.
Lists potential damages resulting from machine overload or incorrect operation.
Information required when ordering replacement parts for the winch.
General| Brand | Tajfun |
|---|---|
| Model | EGV 35 A |
| Category | Farm Equipment |
| Language | English |
To Next Page