Why is the conveyor belt on my Tajfun RCA 400 joy Log Splitter pulling in one direction?
If the conveyor belt on your Tajfun Log Splitter is pulling in one direction, it's due to bad positioning of the driven rollers. Adjust the driven roller so the conveyor belt runs in the middle.
What to do if my Tajfun Log Splitter does not react to control handle commands?
If your Tajfun Log Splitter isn't responding to the control handle, check the following: ensure the electrical cable is connected to the tractor outlet; verify voltage in the socket and correct polarity, switching the tractor lights on and checking the fuses in the machine's electrical box and on the tractor; and ensure the green RESET button (4.1) is pushed before every startup or after opening the safety cover to restore all machine functions.
Why is my Tajfun RCA 400 joy Log Splitter so loud?
Your Tajfun Log Splitter might be loud due to several reasons: excessive P.T.O. shaft rotating speed, which should be checked and kept between 400 and 430 rpm; insufficient oil in the multiplication gear, requiring a check and possible replacement; using a P.T.O. shaft with a built-in clutch (it is recommended to use a regular P.T.O. shaft or one with wide-angle linkages); improper tractor and machine positioning, which requires reconnection according to the instructions; or a P.T.O. shaft that isn't lubricated, needing lubrication according to its instructions.
How to fix a Tajfun RCA 400 joy Log Splitter discharge conveyor that is not operating?
If the discharge conveyor on your Tajfun Log Splitter isn't working, make sure you've pushed the green RESET button before starting. Also, check that the conveyor belt speed regulator isn't set to the lowest position and adjust it accordingly. Ensure the discharge conveyor valve is fully turned down to prevent oil from exiting the cylinder that tensions the belt. Finally, inspect for any wood pieces blocking the rotation and clean the area under the driving roller regularly.
Why does my Tajfun RCA 400 joy Log Splitter vibrate excessively?
Excessive vibration in your Tajfun Log Splitter can be caused by: improper tractor and machine position, which causes vibrations of the P.T.O. shaft, requiring reconnection according to the instructions; or a worn-out P.T.O. shaft, which should be checked and replaced if necessary.
What to do if Tajfun RCA 400 joy feed conveyor belt is not working or slipping?
If the feed conveyor belt on your Tajfun Log Splitter isn't working or is slipping, check the following: ensure the hydraulic pipes for driving the log loader cylinders are properly connected by pushing the couplings deep enough; verify the log loader is connected and the quick couplings under the table are secure with the connecting pipe; check and tension the belt if the roller is slipping; and if the log is too heavy and getting stuck, saw it into shorter pieces.
Why is the chainsaw clutch slipping on my Tajfun RCA 400 joy Log Splitter?
If the chainsaw clutch is slipping on your Tajfun Log Splitter, it could be due to worn clutch plates (replace the clutch plates) or oil leaking on the slide surfaces (determine the source of the oil and clean the slide surfaces).
Why does my Tajfun RCA 400 joy Log Splitter sawbar pull in one direction?
If your Tajfun Log Splitter's sawbar pulls in one direction and cuts sideways, it could be due to a bent sawbar (replace the sawbar), damaged cutting teeth on the chain (sharpen or replace the chain), or the chainsaw damaging the surface of the chainsaw holder (grind off the edge).
Why doesn't my Tajfun RCA 400 joy cylinder return automatically?
If your Tajfun Log Splitter's cylinder performs forward movement but doesn't return automatically (though you can return it using the red button), the final position inductive switch didn't send the signal to return the splitting cylinder. Adjust the position of the switch, located under the machine cover near the splitting cylinder, so it detects the final position of the cylinder.
Why does my Tajfun RCA 400 joy splitting cylinder return too soon?
If the splitting cylinder on your Tajfun Log Splitter starts to split but returns too soon, or returns when you start another function, it's because the splitting valve doesn't remain in the open position due to too low electric power. Check the tractor power output. If you're using a power supply to convert 220V to 12V, check its power output, ensuring it can supply up to 15A of DC current without oscillation, and that you're not using cables with small diameter wires or excessively long cables.
Guidance on connecting the tractor's PTO shaft for power transmission.
Detailed procedure for starting the firewood processor correctly.
Explanation of the control handle and buttons for machine operation.
The process of feeding logs into the processor for cutting and splitting.
Detailed operational steps for the sawing function.
Operational guide for the wood splitting function.
Guidelines for correct and safe use of the splitting wedge.
Schedule for routine maintenance checks and tasks.
Common issues and their solutions for the firewood processor.
Step-by-step instructions for replacing the cutting chain.
General| Model | RCA 400 joy |
|---|---|
| Category | Log Splitter |
| Max Log Diameter | 40 cm |
| Power Source | Electric |
| Motor Power | 7.5 kW |
| Voltage | 400 V |
| Frequency | 50 Hz |
To Next Page