Talius Habitat Screen User Manual

Talius Habitat Screen
TM
Installation Guide
Version 2018.1, 1
©TALIUS
Habitat Screen Installation Guide
If nothing else, at least read this page
Talius has been producing retractable screens since 1998 and in that time we have found that most issues
experienced are related to the product installation. It is essential to follow the installation guidelines. We urge
installers to take the time now to read the instructions and avoid costly, time-consuming problems later. It is
only necessary to read through a small fraction of this booklet as it covers all types of Habitat Screen installations.
At the beginning of each section the booklet will point out if the section can be skipped.
Habitat Screens ship with the screen curtain inside the panel box. This is to facilitate simple installation and save
time. We hope that this installation guide is easy to use. Should you discover an error or an omission please
tell us about it. Parts and options change continually so we are updating all the time.
Should you require any support or have any questions, please call us from site: 800-665-5550
(M-F 8am to 4:30pm PST)
We thank you for putting your trust in us.
Sincerely,
Your Talius Customer Service Team

Talius Habitat Screen Specifications

General

Brand	Talius
Model	Habitat Screen
Category	Window Blinds
Language	English

Summary

Parts Overview

Section One: Opening Criteria

1.1 Panel Box and Shaft Leveling

Ensures the shaft is level for proper tracking and wrinkle-free curtain operation.

1.2 Guide Rails Alignment

Ensures guide rails are plumb and true with equal spacing for proper operation.

1.3 Sill and Floor Slope Considerations

Addresses potential slopes in the sill or floor and options for sealing gaps.

Section Two: Mounting Methods

2.1a Face of Wall Mount

Details mounting the unit against an opening using build-up for clearance.

2.1b Between Jamb and Lintel Mounting

Instructions for mounting the screen inside an opening, ensuring it is level, plumb, and true.

Section Three: Through Wall Operator Prep

3.1a Crank Rod Operator Through Wall

Procedure for drilling holes and routing the crank rod through a wall.

3.1b Motorized Operator Through Wall

Procedure for drilling holes and routing the power cable for motorized units.

Section Four: Pre-drilling Guide Rails

4.1a Face of Wall Mount Drilling

Details hole drilling specifications for guide rails in face of wall mounts.

4.Ib Between Jamb Mount Drilling

Describes pre-drilling or on-site drilling for recessed or build-up between jamb mounts.

Section Five: Mounting Rails and Panel Box

Section Six: Installing the Operator

6.1a Crank Rod Operator Installation

Details installing the crank rod operator, including through-wall routing and rod attachment.

6.1b Motor Operator Installation

Provides critical notes and diagrams for installing tubular motors, emphasizing safety and manufacturer guidelines.

Section Seven: Limit Setting

7.1a Somfy RTS Motor Limit Setting

Step-by-step guide for adjusting upper and lower limits for Somfy RTS motors.

7.1b Standard Limit Motor Limit Setting

Instructions for adjusting limit switches on standard tubular motors using buttons on the motor head.

7.2 General Motor Limit Setting Notes

General advice on motor operation, fabric stretch, and limit setting adjustments.

Limit Setting Common Problems & Solutions

Troubleshooting common issues like motor overheating, limit switch drift, and brake faults.

Section Eight: Securing the Panel Box

Section Nine: Operation and Adjustment

Section Ten: Finishing Touches

9.2 PVC Screw Caps Installation

Instructions for inserting PVC screw caps into mounting holes for a clean finish.

9.3 Bottom Stops Installation

Guidance on installing bottom stops in guide rails for specific Habitat Screen applications.

9.3 Caulking for Water Protection

Using caulking around the panel box and guide rails to prevent water ingress.

Appendix One: Adjustment Guide

Screen Coming Out of Guide Rails

Troubleshooting guide for screen detachment from guide rails, covering shaft centering and rail alignment.

Screen Hanging Up in Guide Rails

Troubleshooting guide for screen snagging in guide rails, checking operator and clearances.