Tapco Side-Winder User Manual

Coil Cradle
Tension Clip
Locking
Knob
Rail Clip
PRO-II
PRO-III
PRO 14™
position
PRO 2000
®
PRO 19™
position
Rail Clip
Tension
Clip
Brake’s Back Rail
Brake’s Front
Base Hinge
STEP 1
Set up is fast and easy. First, install Tension Clip with Locking
Knob onto middle support rail in correct hole position for your
brake. Do not tighten. See illustration above.
STEP 2
Attach Side-Winder to the brake by inserting Back Rail Clip
into the brake's Back (Box) Rail and Tension Clip onto your
brake's Front Base Hinge. Tighten Locking Knob.
Side-Winder
™
Operating Instructions
Loading the Coil Cradle
STEP 3
Remove Cradle Roller from Coil Cradle by grasping and unhooking
Roller Clips at each end. To load coil finish side UP see steps 4a &
4b. To load coil finish side DOWN see steps 5a, 5b & 5c.
COIL CRADLE
Cradle Roller
Roller Clip
Coil Cradle
Roller Tube
NOTE:
Direction of Coil Material
STEP 4a
To load coil finish side UP, insert Coil Cradle into center of coil
then attach Cradle Roller to Coil Cradle over TOP of coil.
Finish Side UP
29797 Beck Road • Wixom, MI 48393-2834
phone: (800) 521-7567 • www.tapcotools.com
Item #12053
T5280-CT 3/06
Kit Contains:
1 pc. 10911 - C-clip
1 pc. 10539 - 1/4 x 1 1/4" lg. Faspin
1 pc. 10913 - Retainer Clip
1 pc. 10799 - 1/4-20 x 1.0" hex washer head screw
Tools Needed:
3/8" wrench
Snap StandSide-Winder
Retainer Clip & C-Clip Installation
Remove the Sidewinder from the box.
Attach the Retainer Clip to the front support with the 1/4-20 x 1.0" hex washer head screw. Use proper hole
as described in figure 1a. The hole will be 14 5/16" from the end if used on a PRO-14 series brake and 19.0"
from the end if used on a PRO-19 series brake. The retainer clip must run parallel with the front support
and point to the left. See figures 1a, 1b, and 1c below.
Install the Sidewinder back on the brake. Insert the C-clip in the front support and fix in place with the 1/4
x 1 1/4" lg. faspin. See Figure 2a at right.
1a
1c
1b
2a
© Boral Building Products Inc.

Tapco Side-Winder Specifications

General

Brand	Tapco
Model	Side-Winder
Category	Power Tool Accessories
Language	English

Summary

Retainer Clip & C-Clip Installation

Attach Retainer Clip

Attaches the retainer clip to the front support using a hex washer head screw.

Install C-Clip

Installs the C-clip in the front support and secures it with a faspin.

Side-Winder Operating Instructions

Initial Setup

Attaches the Tension Clip to the middle support rail and then attaches the Side-Winder to the brake.

Loading the Coil Cradle

Remove cradle roller, load coil material with finish side up or down, and reattach roller.

Coil Holder System

Load Coil Finish Side Down

Loads coil with the finish side facing down into the cradle system.

Attach the Side-Winder to a Brake

Thread Coil

Draws the coil through the Side-Winder and into the brake's open jaws.

Dispense Coil

Dispenses the coil material to the desired length along the brake.

Cut Coil

Cuts the coil to the desired length using the cut-off tool, ready for bending.

SideWinder Parts Diagram