Taurus ACCENTO LATTE - Manual Clean

BREW LATTE
• Place a coffee mug under the coffee outlet.
• Fill the milk tank with the appropriate amount of cold milk.
NOTE: It is recommended that the temperature of the
milk should be 5-10 °C, and the protein content of milk
should be at least 3%.
NOTE:Themilklledinthemilkreservoirshouldnot
exceed the MAX mark on the milk reservoir.
• Insert the milk tube well in place as explained in the milk
tank section in the «Before use» section of the manual.
• PresstheLattebutton(4.4).Theappliancewillstartto
brew a Latte.
• After brewing a Latte, the appliance goes into standby
mode automatically.
• Duringthefunction,presstheLattebutton(4.4)againif
you need to cancel the function.
NOTE: After each use, if there is still milk in the milk res-
ervoir, please store it in the refrigerator, but the silicone
tube and milk frother should be cleaned in time, as it is
explained in the «Cleaning» section of this manual.
NOTE: It is recommended to use a high cup to prevent
the frothed milk from splashing.
• Proceed to clean the milk frothing system as explained in
the «Cleaning» section.
MAKE HOT WATER
• Place a water container under the coffee outlet.
NOTE: The capacity of the water container should be
more than 120 ml.
• Check and make sure the plug of the milk frother is closed
well in place.
• Pressthehotwaterbutton(4.3).Theappliancewillstart
to make hot water.
• After making hot water, the appliance goes into standby
mode automatically.
• Duringthefunction,pressthehotwaterbutton(4.3)again
if you need to cancel the function.
NOTE: Please do not touch the water container with your
hands while making hot water.
CAUTION: After making some water, there could be a
little steam coming out of the machine. When taking the
mug, ensure your hand don’t go under the coffee outlet.
MANUAL FROTH
NOTE: After the Manual froth function is conducted, the
overheating protection mechanism for the boiler will be
activated. At that time, if you need to conduct the hot
water function, the appliance should be rested for about
3-5 minutes, and then the hot water function can be
activated.
• Place a mug under the coffee outlet.
NOTE: The capacity of the milk container should be more
than 160 ml.
• Fill the milk tank with the appropriate amount of cold milk.
NOTE: It is recommended that the temperature of the
milk should be 5-10 °C, and the protein content of milk
should be at least 3%.
NOTE:Themilklledinthemilkreservoirshouldnot
exceed the MAX mark on the milk reservoir.
• Insert the milk tube well in place as explained in the milk
tank section in the «Before use» section of the manual.
• Pressthemanualfrothbutton(4.2).Theappliancewill
start to brew a manual froth.
• After brewing the manual froth, the appliance goes into
standby mode automatically.
• Duringthefunction,pressthemanualfrothbutton(4.2)
again if you need to cancel the function.
NOTE: After each use, if there is still milk in the milk res-
ervoir, please store it in the refrigerator, but the silicone
tube and milk frother should be cleaned in time, as it is
explained in the «Cleaning» section of this manual.
NOTE: It is recommended to use a high cup to prevent
the frothed milk from splashing.
• Proceed to clean the milk frothing system as explained in
the «Cleaning» section.
MANUAL CLEAN
• Place a water container under the coffee outlet.
• Pressthemanualcleanbutton(4.1).Theappliancewill
start to conduct the manual clean function.
• After cleaning, the appliance goes into standby mode
automatically.
• Pressthemanualcleanbutton(4.1)againifyouneedto
cancel the function.