Taurus ALPATEC MSB 2000 - Before Use; Temperature Selection; Set Program

D Timer button
E Open window detector
F OK button
G Heater setting
ASSEMBLING THE WALL BRACKET:
- The appliance has a wall support (Fig.1) to
support the product.
- Fix the wall support as you think appropriate,
using wall plugs, screws, adhesive...
- Taking into account the separation distances
mentioned above, place the wall support in the
required position and mark the drilling points on
the wall (Fig.2).
- Drill on the marks and introduce the plugs
(Fig.3).
- Fit the support, lining up its holes with those of
the plugs, and screw on (Fig.4).
- Make sure that the bracket is rmly xed; it
should be able to support twice the weight of the
appliance.
- Fit the appliance into the wall support.
- Now follow the instructions in Figures 5,6,7.
INSTRUCTIONS FOR USE
BEFORE USE:
- Make sure that all the product’s packaging has
been removed.
- Some parts of the appliance have been lightly
greased, consequently, the appliance may give
off a light smoke the rst time it is used. After a
short time, this smoke will disappear.
- To eliminate the smell given off by the appliance
when used for the rst time, it is recommended
to have it on at full power for 2 hours in a well-
ventilated room.
- Prepare the appliance according to the function
you wish to use.
USE:
- Connect the appliance to the mains.
- Turn the appliance on using the on/off switch(a)
- Turn the appliance on using the on/off button.
(B)
HEATER FUNCTION
- Select the heater function by pressing (G) and
select the desired setting: 1800W ( ), 900W
( ) or fan function.
- Check that the thermostat control is set to the
desired temperature.
TEMPERATURE SELECTION
- Select the desired temperature (5-40ºC) by
pressing (A).
- Press (C) to set the desired temperature and
then press (F) to conrm.
SET DAY & TIME:
- When setting the day and time, the unit has to
be in standby mode.
- Press (A) and the icons
1234567
will light
up, use + or – to set the day, once the required
day is ashing, press (F) to conrm it.
- Press (A) until the hour icon lights up in
order to set the hour, and then OK to conrm it.
- Press (A) until the minute icon lights up
in order to set the minutes, and then OK to
conrm it.
SET PROGRAM:
- When the unit is on standby, press and hold (D)
for 3 seconds , the icon will remain lit until
programming has been completed.
- The icon
1234567
will light up fully, now use
+ or – to select the desired day of the week,
once selected press OK to conrm. Next, the
1 6 12 18
icon will appear in order to
select when the heater is operating, one mark
per hour, use + or – to select the desired hours
and press OK (F) to conrm.
- To program more than one hour, use + or – for
the ON time, press SET (A) and OK (F) to
conrm, and then press OK (F) to program the
OFF time.
- Once nished, the temperature can be set, 20°
by default, use + or – to specify the desired
temperature (5-40) and OK (F) to conrm.
- In this way the whole week, 7 days, can be
programmed.
- When the weekly programming is operational,
the icon will be lit, to switch this off, or on
again, press (D) and the icon will disappear or
reappear.
NOTE: The program is saved even after turning
off. If the appliance is turned of for ve days, all
settings must be made again.
TOWEL WARMING FUNCTION
- Press (E) to switch on the towel warming
function. To cancel this function, press the same
button again.
- During operation, the icon will light up.
- The towel warmer is 200W.