Teac TD-260T - User Manual

To Next Page

Digital Transducer Indicator

TD-260T

D01156700E

Instruction Manual

Main Page

Introduction2
- Features2
- Checking Accessories2
Safety Instructions3
- Table of Contents4
1 Controls and Functions6
- Front Panel6
- Rear Panel8
2 Hardware Installation10
3 Connections11
- Connecting to I/O Terminal Blocks11
  - Connecting to Sensor I/O Terminal Block11
  - Connecting to Control I/O Terminal Block11
- Connecting Strain Gage Sensor12
- Connecting to Power Input Terminals, FG Terminal, and Protective13
- Connecting to Control I/O Terminals14
4 Setup Mode15
- Changing Set Values15
- List of Setup Items and Settings16
5 Error Messages20
6 Calibration21
- Common Calibration Procedure22
- Equivalent Input Calibration25
- Actual Load Calibration27
- TEDS Calibration28
  - Displayed Digits of Rated Capacity for TEDS Calibration29
- Zero-Point Calibration29
7 Setting Functions30
- Setting HI, LO, HH, and LL Values30
- Hysteresis33
- Comparative Output Pattern34
  - Standard Output34
  - Area Output35
- Comparison Mode36
- Near Zero36
- Motion Detection37
  - Motion Detection Time37
  - Motion Detection Bandwidth37
- Zero Tracking38
  - Zero Tracking Time Interval38
  - Zero Tracking Bandwidth38
- Digital Filter39
- Analog Filter39
- SET Lock40
- Static Strain Mode40
- Decision-Output Check41
- Control-Input Check41
- Beep42
- Select Data Output42
8 Hold Function43
- Hold Mode43
- External Hold Mode43
- Enable CLEAR Signal44
- Enable Block Setting44
- Enable JUDGE Signal45
- Sample Hold46
- Peak Hold47
  - Operation Without Block Setting47
  - Operation with Block Setting47
- Bottom Hold48
  - Operation Without Block Setting48
  - Operation with Block Setting48
- Peak-To-Peak Hold49
  - Operation Without Block Setting49
  - Operation with Block Setting49
9 Digital Zero Function50
- Digital Zero50
- Digital Zero Limit50
- Clear Digital Zero51
- Enable Digital Zero51
- Digital Offset52
10 BCD Data Output (TD-260T AC(BCD) / TD-260T53
- DC(Bcd))53
- Panel53
- Changing Logic54
- Equivalent Circuit54
- Signal Timing55
- BCD Data Refresh Rate56
- BCD Output Check56
11 RS-232C Interface (TD-260T AC(232C) / TD-260T57
- Panel57
- Standard57
- Cable Wiring Example58
- RS-232C Interface Setting58
- List of Commands59
- Transmission Mode61
  - Transmission Mode 061
  - Transmission Mode 161
- Format for Transmission Mode 061
  - Read Displayed-Reading Command (RA)61
  - Read Status Command (RS)61
- Set Commands62
- Set-Value Retrieval Command64
- Control Commands65
- Format for Transmission Mode 165
12 D/A Converter (TD-260T AC(D/A) / TD-260T DC(D/A))66
- Panel66
- Connections66
  - Connecting to Screwless Terminal Block66
- D/A Zero67
- D/A Full Scale67
- D/A Output Error68
13 NDIS Panel (PN-260ND)69
14 About TEDS70
- Save TEDS Data70
- Restore TEDS Data71
15 Available Functions at Turn-On72
- Performing Self-Check72
- Initializing Settings72
16 Specifications73
17 Outline Drawings74
18 Block Diagram75

Need help?

Do you have a question about the Teac TD-260T and is the answer not in the manual?

Teac TD-260T Specifications

General

Brand	Teac
Model	TD-260T
Category	Touch Panel
Language	English

Teac TD-260T - User Manual

Table of Contents

Teac TD-260T Specifications