EasyManua.ls Logo

Team Powers XPS-sport - User Manual

Default Icon
11 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1
(Designed & Manufactured by RC EXPLORER TEAM)
XPS Brushless Speed Control System V1.2 User Guidelines
1. Technical /Specifications:
Model:
XPS- Pro XPS-Sport XPS-EL
Continuous current:
140A 70A 40A
Burst Current (10sec):
720A 380A 160A
Battery Input: 3.7V LiPo
2 cells 2 cells 2 cells
1.2V NiMh/NiCd
4-6 cells 4-6 cells 4-6 cells
BEC Output:
Linear 6V/3A Linear 6V/3A Linear 6V/3A
Weight (not include wiring & fan):
~42g ~41g ~40g
Dimension(L x W x H) mm
(Include the fan assembly to the ESC)
~33 x 34 x 29 ~33 x 33 x 29 ~33 x 33 x 29
Motor limit with 2cell x 3.7V Lipo.
The motor timing is at 0 degree
4 Turn or over
6.5 Turn or over 9.5 Turn or over
2. Features:
＊ Support all kinds of sensor/sensorless brushless motors in RC model 1/10
th
, 1/12
th
Car & Truck
＊ XPS Pro and Sport Speed control can support Turbo mode function for modify and stock mode
motor.
＊ Include zero timing mode function. Orange LED blinking indicates zero timing mode at neutral
position.
＊ Support Running Mode: Forward with brake, Forward/Reverse, Forward/Reverse with Brake
＊ Manual Power profile: It can adjust the setting of the throttle/ brake power profiles
＊ One touch On/Off switch which are located on top of speed control. It can eliminate the
problem of the switch wire being cutting off under collision and can save some space for the rc car
chassis
＊ Use the pocket-size LCD program card to program the controller settings
＊ Multiple protection functions: Low voltage cut-off protection, Overheat protection, Throttle
signal loss protection.

Table of Contents

Questions and Answers

  • D
    Dwayne HendersonAug 9, 2025
    Why is there radio interference with my Team Powers XPS-sport?
    • C
      Caleb PattonAug 9, 2025
      Radio interference with your Team Powers Controller can stem from several factors. It could be due to empty transmitter batteries, so try replacing them. A bad battery connection might also be the culprit; in this case, check the wire connections. The receiver, transmitter, or servo might be defective, so replace these components one by one to identify the issue. Also, ensure the receiver or antenna aren't too close to the power wires of the motor and battery; if they are, change the location of the components.
  • J
    Jo SmithAug 14, 2025
    What to do if my Team Powers XPS-sport Controller has no motor and servo functions?
    • V
      valerie28Aug 14, 2025
      If your Team Powers Controller exhibits no motor and servo functions, begin by checking the wires and connectors for any wiring problems. Ensure that the polarity is correct when connecting the BEC wire to the receiver. If these steps don't resolve the issue, the transmitter, receiver, or battery might be defective; replace these components one by one to identify the faulty part. If all else fails, the speed control might be defective and require repair.
  • M
    Mr. Jared TorresAug 20, 2025
    What to do if my Team Powers Controller has no motor function, but servo is working?
    • J
      jamieramirezAug 20, 2025
      If your Team Powers Controller has no motor function but the servo is working, start by checking the wires and connectors for any wiring issues. A defective or missing sensor wire could also be the cause, so try changing the sensor wire. The motor itself might be defective, so try changing the motor. If these steps don't solve the problem, the speed control might be defective and require repair.
  • S
    Samuel JohnsonAug 27, 2025
    Why does the motor stutter while accelerating with my Team Powers XPS-sport Controller?
    • D
      Deborah HoweAug 27, 2025
      If the motor stutters while accelerating with your Team Powers Controller, consider these potential causes: * The sensor wiring might be defective; try replacing the wire. * The motor or sensor board could be defective; try changing the motor or sensor board. * A power capacitor failure could be the issue; replace the power capacitor. * Radio interference might be the cause; change the location of the components. * The speed control might be defective and require repair.
  • S
    sarahsmithSep 1, 2025
    How to fix a Team Powers Controller when the motor runs at a constant slow speed and never stops?
    • J
      Julie Williams DDSSep 1, 2025
      If the motor runs at a constant slow speed and never stops with your Team Powers Controller, it might be due to changed transmitter settings after setup; in that case, repeat the setup procedure. Alternatively, humidity or water in the speed control could be the issue; try drying the speed control.

Summary

Technical Specifications

Features

Connection Diagram

Speed Control Setup

Transmitter Settings

Configures transmitter functions like throttle, brake, and servo settings before speed control setup.

Set Neutral, Forward and Brake Endpoint Data

Calibrates the speed control's neutral, full throttle, and full brake positions using the transmitter stick.

Double Check Speed Control Function

Mode Programming

Mode Functions Explanation

Program Card Specifications

Program Card Operation

Details the process of connecting and using the program card with the speed control for configuration.

Step 1: Connection with Speed Control

Guides on connecting the program card to the speed control's BEC wire for initial setup.

Program Card Settings

Step 2: Program Mode Function Settings

Explains how to navigate and change settings using the program card interface menu.

Reset All Setting Parameters

Describes how to restore the speed control's settings to factory defaults via the program card.

Firmware Version Display

Instructions on how to view the firmware version of the speed control on the program card.

Troubleshooting Table

Warning Notes

Warranty Services

Team Powers XPS-sport Specifications

General IconGeneral
BrandTeam Powers
ModelXPS-sport
CategoryController
LanguageEnglish

Related product manuals