Technics SH-AV22

HSNMONA
Technical
Specifications
(DIN 45 000)
@ AUDIO SECTION
Input sensitivity/input impedance
SOURCE
INPUT
150
mV/100
kQ
TV/VIDEO
150
mV/100
kQ
VCR
1/TAPE
1,
VCR
2/TAPE
2
(PLAYBACK) 150 mV/100 kQ
GRAPHIC EQ/EXT. (INPUT) 150 mV/20 kQ
MIC
1.5
mV/10
kQ
Output voltage/output impedance
SOURCE
OUTPUT
150
mV/20
kQ
VCR
1/TAPE
1,
VCR
2/TAPE
2
(REC
OUT)
150
mV/470
Q
GRAPHIC
EQ/EXT.
(OUTPUT)
150
mV/2.2
kQ
S/N (surround sound OFF)
SOURCE, VCR 1/TAPE 1,
VCR 2/TAPE 2: 90 dB (DIN 45 500)
(OUTPUT: SOURCE OUT) 82 dB (IHF ’66)
Frequency response (surround sound OFF)
SOURCE 5 Hz ~ 100 kHz +0 dB, ~3 dB
TV/VIDEO
5
Hz
~
100
kHz
+0
dB,
~3
dB
VCR 1/TAPE 1,
VCR
2/TAPE
2
5
Hz
~
100
kHz
+0
dB,
~3
dB
MIC
40
Hz
~
13
kHz
+0
dB,
-3
dB
Maximum input voltage (1 kHz)
SOURCE, TV/VIDEO, VCR 1/TAPE 1,
VCR
2/TAPE
2
5.5V
MIC
80
mV
Total
harmonic
distortion
SOURCE INPUT (at 1 kHz) 0.003%
MIC (at 1 kHz) 0.03%
@ FUNCTIONS
BGYV
(back
ground
video)
Sound
selected
by
input
selector is heard while
watching selected video
source; can also be mixed with
video source sound; mix level
controlled by BGV mixing level
; control.
Surround
sound
on/off
Included.
Surround
sound
mono/stereo
Selectable
according
to
input
signal
mode.
Microphone
mixing
Microphone
sounds
can
be
mixed with audio and/or video
source sounds; mix level
controlled by microphone
mixing level control.
@ VIDEO SECTION
Input voltage/input impedance
TV/VIDEO, VCR 1/TAPE 1,
VCR
2/TAPE
2
1.0
Vp-p/75
Q
Maximum
input
voltage
2.0
Vp-p
Output
voltage
:
{input
:
1
Vp-p,
load
75Q
unbalanced)
TV/VIDEO,
VCR
1/TAPE
1,
VCR
2/TAPE
2
1
Vp-p
@ GENERAL
Power
consumption
13
W
Power
supply
AC
50
Hz/60
Hz,
110V/127V/220V/240V
Dimensions
(WXHXD)
430
x
86
X
236
mm
(16-15/16"x3-5/32"x9-31/32")
Weight
2.8
kg
(6.2
Ib)
Troubleshooting
Guide
Before
requesting
service
for
this
unit,
check
this
table
to
deter-
mine
if
the
problem
can
be
solved
as
described
below.
If
the
problem
still
persists
after
making
these
checks,
or
if
there
are
symptoms
of
malfunction
not
described
in
this
table,
it
is
recom-
mended that you consult the store where this unit was purchased
or your local Servicenter (see list included) for further infor-
mation and assistance.
Suggested remedy
© Check to be sure that all connection wires are
correctly connected. (See page 6 and 7)
© Set to the “AV source” position.
e Adjust the volume level of this unit.
# Adjust the volume level of the amplifier or receiver.
Check to be sure that the selectors are set
to the correct position.
e Adjust the audio/video surround-sound effect
control.
Set to the “on” position.
eSet to the “mono” position.