Technics SX-K350

EXPLANATION OF FUNCTIONS
1. KEYBOARD SPLIT
Normally, the entire keyboard can be used to play a melody using poly presets and/or solo presets tones.
However, while using the Auto Play Chord, etc., the keyboard splits into two sections: accompaniment on the
left side and melody on the right.
Button Settings Notes/Section
The melody can be
played using the entire
keyboard.
® Cancel button on
and split accomp
button off
split poly solo ® PCC button on
accomp presets presets
cS a ee
Cancel and split The left section is for
accomp buttons accompaniment and
on the right for melody
One finger (split condition).
button on
Fingered button
espe Pe | =
cancel @@ onefinger fingered memory
L_ auto play chord J
@ Up to 8 notes can be played at once only when the cancel
button is on and the split accomp button is off. In all other
situations, up to 4 notes in each section can be played at
once. However, only one note can be played using the solo
presets.
e The position of the split on the keyboard between the
sections for accompaniment (left) and melody (right) can
be programmed by using the following procedure.
1. Press the M22N9 button. The button will flash.
2. Press the split accomp button. It slowly flashes.
3. Press the key where you desire the sections to be split.
(The key you pressed and those to the right can be used
to play melody.)
Musical=Display=
Example: When the C key of octave level 3 is pressed.
The name of the depressed key and its octave level are
displayed.
io eae Se of
ur
m 4 +54
(K450 only)
eeseaeas a: Keys for accompaniment eae! eee Keys for melody |
errr adartaret erence ane tre
=
/
L
"ome!
‘oan!
spli
|
|
This number corresponds to the number of the
keyboard octave of the following figure.
In the initial mode, the split position is 2G.
@ Accomp Octave Up
accomp octave up
Pressing this button raises the accompaniment by one [=]
octave when the split accomp button is on.
2. VOICE COMBINATIONS
Seven kinds of registration combining voices and effects are
preset. This allows any desired voice combination to be
easily selected.
Setting procedure:
1. Press the button to turn it on.
2. Press any one of the keys I through VI.
| aaa church organ \) ener new wave
UE ieee classical strings VI ....mix combo |
lil ....big band brass VII....mix combo II
IV. ....funk rock
3. PLAY SEQUENCER
fe... voice combinations
church Classical big band — funk
organ strings if
new wave mix mix
‘ass rock combo | combo I
The Piay Sequencer is used to make a “real time” recording
of a performance. The performance is digitally recorded into
the keyboard’s computer memory, providing the same
results as if the recording were on tape.
A performance can be stored in four separate parts:
bass....Stores bass sounds.
left ..... Stores an accompaniment. The organ, string
ensemble and guitar voices in the rhythmic
orchestra section are stored in this section.
right....Stores a melody using the poly presets and/or solo
presets.
solo ....... Stores a melody using the solo presets.
If solo part is to be stored in your performance, the
solo presets button in the Orchestral Conductor
should be turned off during recording of the right
section.
Thus, by automatically playing back these four buttons, an
ensemble effect can be obtained as if you were playing the
bass, melody, accompaniment and solo keyboards at the
same time.
@ Storage
(1) Registration settings
1. IMPORTANT — Setall desired voices, rhythm, and effects
before pressing the MEM button. If an introduction is
needed, press fill in & intro now.
The Play Sequencer stores the entire performance, which
includes melody, accompaniment, and changes in registra-
tion, effects, and rhythm.
Pray Sequencer
MT bass lett right solo
Ew Sw es Es
© The optional memory pack (SY-P2 or SY-P3) can be used
to store your performance.